Password Procedure - ABB 691HT Operating Instructions Manual

P A S S W O R D
E N A D I S A
B L E B L E
I n p u t n u m e r i c
p a s s w o r d :
[ _ _ _ _ _ _ _ ]
CL R E N T R
R e t y p e p a s s w o r d :
[ _ _ __ _ _ _ ]
C L R E N T R
P a s s w o r d e n a b l e d
P re s s a n y k e y t o
c o n t i n u e
P a s s w o r d a l r e a d y
e n a b l e d
C H N G
I n p u t e x i s t i n g
p a s s w o r d :
[ _ _ _ _ _ _ ]
CL R E N T R
I n p u t n e w
p a s s w o r d :
[ _ _ _ _ _ _ ]
CL R E N T R
R e t y p e n e w
p a s s w o r d :
[ _ _ _ _ _ _ ]
C L R E N T R
I n p u t e x i s t i n g
p a s s w o r d :
[ _ _ _ _ _ _ ]
CL R E N T R
- 10 -

PASSWORD PROCEDURE

If you want to enable the password or to change the existing one press
the F4 function key, corresponding to the label PASSWORD in the main
menu. The password menu will appear. The possible password operation
are the following:
- setting a password and enabling it.
- changing an existing password and enabling it
- disabling a password
Setting a password. If you want to set a password press the function
key F1, labelled ENABLE: If the password is already enabled, then a new
display, shown below, gives the possibility to change the existing
password or to proceed without changing it. Otherwise, pressing F1,
appears the following:
Insert the numeric password: it can be any number from 1 to 6 digits.
If a mistake is made, the CLR key should be pressed to start again.
After entry as been completed pressing the ENTeR key a new display
appears asking to repeat the entry for security reasons.
Pressing the ENTeR key the next screen appears confirming that the
password has been successfully entered and enabled: if for some
reason the procedure aborts then the following message is displayed:
"Password incorrect - Press any key to continue "
In both cases, pressing any key you will return to the Password Main
Menu: then press ESCape if you wish to leave the password procedure.
NOTE - Be extremely careful not to forget an entered password, as
the user has no way of circumventing the security feature.
Changing an existing password. If a password exists and is enabled,
the following screen will appear when the F1 key, corresponding to
enable, is pressed. Pressing the F4 key you will return to the Password
P R O
Main Menu while pressing F1 to CHaNGe the following display appears.
C E E D
Input the existing password. If the password is not correct then the
following message is displayed: "Password incorrect - Press any key
to continue ". Pressing any key you will return to the Password Main
Menu.
If the password is accepted then the next screen appears: insert the new
numeric password. If a mistake is made, the CLR key should be pressed
to start again. After entry has been completed pressing the ENTeR key
a new display appears asking to repeat the entry for security reasons.
Pressing the ENTeR key a screen appears confirming that the password
has been successfully entered and enabled: if for some reason the
procedure abort then the following message is displayed:
"Password incorrect - Press any key to continue "
In both the case, pressing any key you will return to the Password Main
Menu: then press ESCape if you wish to leave the password procedure.
Password disable . If you select, from the Password Main Menu, the
DISABLE option, then the following screen is presented: insert the
existing numeric password and then press F4 to ENTeR.
The following message is displayed: " Password disabled - Press any
key to continue".
Note - If you have unlackely forgotten the Password, please contact your
nearest ABB Instrumentation Service Center.
If the password is already disabled or some mistake is made inputting
the password, one of the following messages will be displayed:
" Password already disabled - Press any key to continue "
" Password incorrect - Press any key to continue ".
In both cases, pressing any key you will return to the Password Main
Menu: then press ESCape if you wish to leave the password procedure.