Summary of Contents for NorthStar DOC0056
- Page 1 OPEN NSTALLATION NSTRUCTIONS NSTALLING NDOOR ABINET DOC0056 SiteTel Sweden AB Haukadalsgatan 8A, SE-164 40 Kista, Sweden www.northstarbattery.com Page i...
-
Page 2: Table Of Contents
The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. NorthStar SiteTel shall have no liability for any error or damage of any kind resulting from the use of this document. -
Page 3: Introduction
OPEN NTRODUCTION This document describes how to install the Indoor Cabinets. ARGET ROUP The target group for this document is the personnel involved in the installation and maintenance of the site. REREQUISITES All performance statement in this document relies on the following: ... -
Page 4: Medium
OPEN NSTALLING THE NDOOR ABINET MALL NDOOR ABINET EDIUM 2.1 U NPACKING AND PREPARING This section describes how to unpack and check the delivered equipment for damage. The cabinet is delivered in a flat pack. The following items are included: Content of the Packaging Item Designation Quantity... -
Page 5: Assembling The Indoor Cabinet Small And Indoor Cabinet Medium
OPEN 2.2 A SSEMBLING THE NDOOR ABINET MALL AND NDOOR ABINET EDIUM Note: It is important to initially, not tighten the screws. 1. Put one of the two side walls on the floor, see figure 1 below. Front Bottom Figure 1 Put the side wall on the floor 2. - Page 6 OPEN Upside Floor Figure 2 Back side of the shelf facing the floor Figure 3 Align the shelves to the side wall. 3. Take the other side wall and align the shelves to the wall and attach them to the front side of the wall using M6x20 screws, see figure 4 below.
- Page 7 OPEN Figure 4 Align the shelves to the other side wall. 4. Raise the cabinet to a standing position, see figure 5 below. Figure 5 The Cabinet in a standing position seen from behind. 5. Take out the provided cross bars and assemble them loosely together in pairs using M6x20 screws and M6 lock nuts, see figure 6 below.
- Page 8 OPEN Figure 6 Assembling the cross bars. 6. Attach the first pair of cross bars to the side walls using M6x20, according to figure 7 below. Start with the top part and fasten the cross loosely using M6x20 screws. Note: The Indoor Cabinet Medium has crossbars of two different lengths, the longer crossbars should be attached at bottom.
- Page 9 OPEN 7. Attach the second pair of cross bars to the first pair, and to the battery shelf in the middle of the cabinet using M6x20 screws according to figure 8 below. Note: It is important that you attach the cross bars in the correct positions, see figure 8 below.
- Page 10 OPEN 10. Attach the roof to the side walls using M6x20 screws, see figure 10 below. 11. Tighten all the screws to a torque of 6 Nm. Figure 10 Attach the roof to the side walls. 12. Remove any insulation from the rear grounding screws. 13.
-
Page 11: Medium To The Floor
OPEN NCHORING NDOOR ABINET MALL AND NDOOR ABINET EDIUM TO THE FLOOR The Cabinet must be secured to the floor to prevent it from tipping over and causing personal injury or damaged equipment. Use the screws and plugs appropriate for the foundation material. -
Page 12: Indoor Cabinet Medium
OPEN PTIONAL INCH RACKETS FOR NDOOR ABINET MALL AND NDOOR ABINET EDIUM The 19inch Brackets is delivered in a flat pack. The following items are included: Content of the Packaging Item Designation Quantity 19inch Bracket Torx Screw M6x20 1. When the equipment arrives, check that the packaging is undamaged. 2. - Page 13 OPEN Figure 13 The 19inch Brackets Note: Use the outer holes to attach the 19inch Brackets. 5. Tighten the screws to a torque of 6 Nm. Document Number: INS-0038 Revision: Prepared by: Mikael Lindevall Date: 2012-04-26 Approved by: Ulf Krohn Status: RELEASED Page 11...
-
Page 14: Installing The Indoor Cabinet Large
OPEN NSTALLING THE NDOOR ABINET ARGE 5.1 U NPACKING AND PREPARING This section describes how to unpack and check the delivered equipment for damage. The cabinet is delivered in a flat pack. The following items are included: Content of the Packaging Item Designation Quantity Sidewall with self-clinching nuts... -
Page 15: Assembling The Indoor Cabinet Large
OPEN 5.2 A SSEMBLING THE NDOOR ABINET ARGE Note: It is important to initially, not tighten the screws. 1. Put one of the two side walls on the floor, see figure 14 below. Front Bottom Figure 14 Put the side wall on the floor 2. - Page 16 OPEN Upside Floor Figure 15 Back side of the shelf facing the floor Figure 16 Align the shelves to the side wall. 3. Take the other side wall and align the shelves to the wall and attach them to the front side of the wall using M6x20 screws, see figure 17 below. Note: Do not tighten the screws at this moment.
- Page 17 OPEN Figure 17 Align the shelves to the other side wall. 4. Raise the cabinet to a standing position, see figure 18 below. Figure 18 The Cabinet in a standing position seen from behind. 5. Take out the provided cross bars and assemble them loosely together in pairs using M6x20 screws and M6 lock nuts, see figure 19 below.
- Page 18 OPEN Figure 19 Assembling the cross bars. 6. Attach the first pair of cross bars to the side walls using M6x16 screws, according to figure 20 below. Start with the top part and fasten the cross loosely using M6x20 screws. Note: Do not tighten the screws at this moment.
- Page 19 OPEN 7. Attach the second pair of cross bars to the first pair using M6x20 screws according to figure 21 below. Note: It is important that you attach the cross bars in the correct positions, see figure 20 below. Figure 20 The cross bars attached in the correct positions 8.
- Page 20 OPEN Figure 22 Attach the roof to the side walls. 12. Remove any insulation from the rear grounding screws. 13. Put on the contact washers and the nuts on the grounding screws. Figure 23 The rear grounding screws Document Number: INS-0038 Revision: Prepared by:...
-
Page 21: Anchoring Indoor Cabinet Large To The Floor
OPEN NCHORING NDOOR ABINET ARGE TO THE FLOOR The Cabinet must be secured to the floor to prevent it from tipping over and causing personal injury or damaged equipment. Use the screws and plugs appropriate for the foundation material. 1. Mark the positions on the floor of the four bolts, see figure 24 below. Note: The Cabinet can be used as a template.