Table of Contents
Advertisement
If engine stalls or machine loses headway and cannot
make it to the top of a slope, do not turn machine
around. Always back slowly straight down the slope.
DON'T TAKE AN INJURY RISK! When a person or
pet appears unexpectedly in or near the operating area,
STOP OPERATION. Careless operation, combined
with terrain angles, ricochets, or improperly positioned
guards can lead to thrown object injuries. Do not
resume operation until area is cleared.
Do not touch engine or muffler while engine is running
or soon after it is stopped. These areas could be hot
enough to cause a burn.
Before getting off the seat:
– Move traction pedal to neutral position and remove
foot from pedal.
– Set the parking brake and disengage the PTO.
– Shut the engine off and remove the key from the
ignition switch. Wait for all movement to stop
before getting off the seat.
Lower the blower to the ground and remove key from
ignition switch whenever machine is left unattended.
Maintenance
Remove key from ignition switch to prevent accidental
starting of the engine when servicing, adjusting or
storing the machine.
Perform only those maintenance instructions described
in this manual. If major repairs are ever needed or
assistance is desired, contact an Authorized Toro
Distributor.
To reduce potential fire hazard, keep the engine free of
excessive grease, grass, leaves and accumulations of
dirt. Never wash a warm engine or any electrical parts
with water.
Be sure machine is in safe operating condition by
keeping nuts, bolts and screws tight. Check the rotor
bearing mounting bolts and nuts frequently to be sure
they are tightened to specification.
Make sure all hydraulic line connectors are tight, and all
hydraulic hoses and lines are in good condition before
applying pressure to the system.
Keep body and hands away from pin hole leaks in
hydraulic lines that eject high pressure hydraulic fluid.
Use cardboard or paper to find hydraulic leaks.
Hydraulic fluid escaping under pressure can penetrate
skin and cause injury. Fluid accidentally injected into
the skin must be surgically removed within a few hours
by a doctor familiar with this form of injury or gangrene
may result.
Before disconnecting or performing any work on the
hydraulic system, all pressure in system must be
relieved by stopping engine and lowering blower to the
ground.
If the engine must be running to perform a maintenance
adjustment, keep hands, feet, clothing and other parts of
the body away from the fan and other moving parts.
Do not overspeed the engine by changing governor
settings. To be sure of safety and accuracy, have an
Authorized TORO Distributor check maximum engine
speed with a tachometer.
Engine must be shut off before checking oil or adding
oil to the crankcase.
At the time of manufacture the blower conformed to
safety standards in effect for riding mowers. Therefore,
to ensure optimum performance and safety, always
purchase genuine TORO replacement parts and
accessories to keep the Toro all TORO. NEVER USE
"WILL–FIT" REPLACEMENT PARTS AND
ACCESSORIES MADE BY OTHER
MANUFACTURERS. Look for the TORO logo to
assure genuineness. Using unapproved replacement
parts and accessories could void the warranty of The
Toro Company.
Sound Pressure Level
A GM 2XX series traction unit with the debris blower
attachment has an equivalent continuous A–weighted sound
pressure at the operator ear of: 98 dB(A), based on
measurements of identical machines per SAE Jl174– Mar
85 procedures.
Sound Power Level
A GM 2XX series traction unit with the debris blower
attachment has a sound power level of: 110 dB(A) / I pW,
based on measurements of identical machines per
prbcedures outlined in Directive 79/113/EEC and
amendments.
Vibration Level
Hand–Arm
A GM 2XX series traction unit with the debris blower
attachment does not exceed a vibration level of 4.0 m/s
the hands based on measurements of identical machines per
ISO 5349 procedures.
Whole Body
A GM 2XX series traction unit with the debris blower
attachment does not exceed a vibration level of 0.5 m/s
the posterior, based on measurements of identical machines
per ISO 2631 procedures.
4
2
at
2
at
Advertisement
Table of Contents
