Toro 30393 Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Blower
  5. 30393
  6. Operator's manual
Toro 30393 Operator's Manual

Toro 30393 Operator's Manual

Debris blower for groundsmaster 7200/7210 traction unit
Hide thumbs Also See for 30393:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual
Form No. 3356-435 Rev A
Debris Blower
for Groundsmaster
®
7200/7210 Traction Unit
Model No. 30393—Serial No. 270000001 and Up
Register at www.Toro.com.
Original Instructions (EN)

Advertisement

Table of Contents
loading

Related Manuals for Toro 30393

Summary of Contents for Toro 30393

  • Page 1 Form No. 3356-435 Rev A Debris Blower for Groundsmaster ® 7200/7210 Traction Unit Model No. 30393—Serial No. 270000001 and Up Register at www.Toro.com. Original Instructions (EN)

  • Page 2: Table Of Contents

    Important calls attention to special mechanical information and Note emphasizes general information You may contact Toro directly at www.Toro.com for worthy of special attention. product and accessory information, help finding a dealer, or to register your product.

  • Page 3: Safety

    A free replacement manual is available that no one is behind the machine. by sending the complete Model and Serial Number to The Toro® Company, 8111 Lyndale Avenue – Watch out for traffic when near or crossing South, Bloomington, Minnesota 55420-1196.

  • Page 4: Safety And Instructional Decals

    Hydraulic fluid escaping under pressure can purchase genuine Toro replacement parts and penetrate skin and cause injury. Fluid accidentally accessories to keep the machine all Toro. Never injected into the skin must be surgically removed use “will-fit” replacement parts and accessories within a few hours by a doctor familiar with this made by other manufacturers.
  • Page 5 114-4054 1. Warning—read the Operator’s Manual, do not operate the machine without the cross pin in place. 105-4593 1. Entanglement hazard, shaft—do not remove cover while parts are moving, keep all guards in place.

  • Page 6: Setup

    Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Mount the castor wheel to the debris Castor wheel assembly blower Debris blower assembly Mount the debris blower to the traction Locking pin unit Hair pin cotter –...
  • Page 7 5. Insert the locking pin through the adapters and secure with a hairpin cotter (Figure 5). Mounting the Debris Blower to the Traction Unit Parts needed for this procedure: Debris blower assembly Locking pin Hair pin cotter Procedure 1. Remove any attachment from the rear of the G006618 machine.

  • Page 8: Adjusting The Link Assembly

    Adjusting the Link Assembly Grease the Blower No Parts Required No Parts Required Procedure Procedure 1. With the debris blower mounted and secured on the traction unit, raise the attachment. Before the Debris Blower is operated, it must be greased to assure proper lubrication.
  • Page 9 72" width of cut GM7200 & GM7210 with NO Additional Weight Hard Canopy (model 30359) Fr ont Weight Part Weight Models 30360, 30361, 30363, & 30364 Requir ed Number Description Rear QAS and no attachment 0 lb. (Model 30377) QAS Finish Grader (Box Rake) 0 lb.
  • Page 10 62" width of cut GM7200 & GM7210 with NO Additional Weight Hard Canopy (model 30359) Fr ont Weight Part Weight Models 30362 & 30365 Requir ed Number Description Rear QAS and no attachment 67 lb. 114-4090 & Front Weight Bracket & (Model 30377) 114-4096 42 lb.

  • Page 11: Operation

    Operation Adjust Discharge Opening The discharge opening (Figure 9) is adjustable to direct the air flow from the blower. 1. Loosen discharge opening deflector mounting screws (Figure 9). Figure 10 1. Float 3. Lift/Lower 2. Power down Operating Tips Discharged air has considerable force and could cause injury or loss of footing.
  • Page 12 G003783 Figure 11 1. Pry slot...

  • Page 13: Maintenance

    Maintenance Greasing the Attachment Adapter If the locking lever on the attachment adapter does not Lubrication pivot freely and easily, apply a light coat of grease to the area shown in Figure 14. The debris blower has bearings and bushings that must be lubricated regularly..

  • Page 14: Torquing Fasteners

    G003815 G003816 Figure 16 Figure 17 1. Motor coupler 3. Set screw (2 each) 1. Set screw 2. Fan coupler 4. Coupler spider • The fan mounting nut (Figure 18) must be torqued 3. Tighten the capscrews and nuts securing the to 500 ft–lb.

  • Page 15: Servicing The Castor Wheels And Bearings

    1. Raise the debris blower so that the wheels are off of the floor. Block the blower so that it cannot accidentally fall. 2. Remove the tensioning cap, spacer, and thrust washer from the top of the castor spindle. 3. Pull the castor spindle out of the mounting tube. Allow the thrust washer and spacer to remain on the bottom of the spindle.
  • Page 16 If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.

Table of Contents