Related Manuals for Toro 30855
Summary of Contents for Toro 30855
- Page 1 Form No. 3350–248 Debris Blower Groundsmaster 300 Series Attachment Model No. 30855—Serial No. 230000001 and Up Operator’s Manual English (EN)
-
Page 2: Table Of Contents
Authorized Service allow adults to operate machine without proper Dealer or Toro Customer Service and have the model and instruction. Only trained operators who have read this serial numbers of your product ready. The two numbers are manual should operate this machine. -
Page 3: While Operating
Keep all shields and safety devices in place. If a shield, This product may exceed noise levels of 85 dB(A) at safety device, or decal is illegible or damaged, repair or the operator position. Ear protectors are recommended replace it before operation is commenced. Also tighten for prolonged exposure to reduce the potential of any loose nuts, bolts, and screws to ensure that the permanent hearing damage. -
Page 4: Maintenance
Toro replacement parts and accessories to keep the machine all Toro. Never use E. Set the parking brake and disengage the PTO. “will-fit” replacement parts and accessories made by F. -
Page 5: Safety And Instruction Decals
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 98-3113 1. Warning—stop the engine and remove the key before leaving the machine or disconnecting the PTO shaft;... - Page 6 105-0707 99-4487 1. Read the Operator’s 3. Grease every 8 hours. Manual. 4. Grease every 100 hours. 2. Grease 105-0698 Place over decal 105–0707 for CE 1. Warning—read the Operator’s Manual. 105-0708 1. Warning—thrown objects 99-4486 1. Entanglement hazard, belt—stay away from moving parts.
-
Page 7: Specifications
Specifications Note: Specifications and design subject to change without notice. General Specifications Backward curved, cast aluminum fan. 12 blades per side, 21 in. (53 cm) outside diameter, 6-3/8 in. (16 cm) width, 34 lb. (16 kg) 10 gauge steel face plates welded to 10 gauge wrapper. Increasing scroll from Fan housing cutoff. -
Page 8: Setup
Operator’s Manual Read before operating the machine. Parts Catalog Registration card Fill out and return to Toro. Note: Determine the left and right sides of the machine from the normal operating position. Installing the Castor Wheel Assemblies The castor wheel assemblies are installed upside down on the debris blower for shipping. -
Page 9: Installing The Stand
Do not remove the ball joint mounts from 3. Position the traction unit in line with the rear of the the lift arms. The lift arms must be equipped with Toro Debris Blower. ball joint mounts, Part No. 21-3050 and 21-3020. -
Page 10: Installing The Drive Shaft
(Part No. 24-5790) are installed. Order two Weight down. Kits, Part No. 24-5780 and one Weight Kit, Part No. 24-5790 from your Toro Distributor. 9. Pivot the blower rearward and secure the lift bracket to the T-bar on the traction unit with the lift arm bracket Greasing the Blower and pin. -
Page 11: Operation
Operation Note: Determine the left and right sides of the machine Adjusting the Discharge from the normal operating position. Opening Operating Tips The discharge opening is adjustable to increase or decrease air output velocity and volume. Decreasing the discharge opening size will increase the velocity. Warning 1. -
Page 12: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Lubrication Idler Arm Bearing The idler arm bearing (Fig. 8) must be lubricated after every 8 hours of operation with a No. 2 Lithium-based grease. -
Page 13: Adjusting The Blower Belt
Adjusting the Blower Belt 3. When the belt stretches, adjust it as follows: A. Loosen the nuts securing the belt tensioner to the Make sure belt is properly tensioned to ensure proper blower housing. operation of the machine and unnecessary wear. Check belt frequently. -
Page 14: Troubleshooting
Troubleshooting Problem Possible Causes Corrective Action The fan quits turning. 1. The bolt on the PTO adapter 1. Replace the bolt. may be sheared. There is excessive vibration. 1. The bearing on the fan shaft is 1. Replace the bearings. damaged. -
Page 15: Storage
Storage 1. Thoroughly clean the blower. The fan housing should be free of dirt, leaves, and debris. 2. Lubricate all grease fittings. Wipe off any excess lubricant. 3. Place a light coat of grease on the splines of the PTO adapter. -
Page 16: The Toro General Commercial Products Warranty
If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.