Toro 74310 Operator's Manual page 59

Problem
The engine loses power.
The engine overheats.
The mower pulls left or right (with levers
fully forward).
The machine does not drive.
The machine vibrates abnormally.
The machine produces an uneven cutting
height.
The blades do not rotate.
Possible Cause
1. The engine load is excessive.
2. The air cleaner is dirty.
3. The oil level in the crankcase is low.
4. The cooling fins and the air passages
above the engine are plugged.
5. The vent hole in the fuel cap is plugged.
6. There is dirt in the fuel filter.
7. There is dirt, water, or stale fuel in the
fuel system.
1. The engine load is excessive.
2. The oil level in the crankcase is low.
3. The cooling fins and the air passages
above the engine are plugged.
1. The tracking needs adjustment.
2. The tire pressure in drive tires not
correct.
3. The reverse indicator and
speed-control linkage need adjustment.
1. The bypass valves are not closed tight.
2. The pump belt is worn, loose or broken.
3. The pump belt is off a pulley.
4. The idler spring is broken or missing.
5. The hydraulic fluid level is low or too
hot.
1. The cutting blade(s) is/are bent or
unbalanced.
2. The blade mounting bolt is loose.
3. The engine mounting bolts are loose.
4. There is a loose engine pulley, idler
pulley, or blade pulley.
5. The engine pulley is damaged.
6. The blade spindle is bent.
7. The belt is damaged.
1. The blade(s) is/are not sharp.
2. The cutting blade(s) is/are bent.
3. The mower deck is not level.
4. The underside of mower is dirty.
5. The tire pressure in drive tires not
correct.
6. The spacers are in the wrong location.
7. The tips of adjacent blades are at an
uneven cutting height. Blades tips
should be even within 3/16 inch which
is approximately one blade thickness.
1. The PTO belt is worn, loose, or broken.
2. The PTO shaft is not connected.
3. The PTO belt is off the pulley.
59
Corrective Action
1. Reduce the ground speed.
2. Clean the air-cleaner element.
3. Add oil to the crankcase.
4. Remove the obstruction from the
cooling fins and the air passages.
5. Clean or replace the fuel cap.
6. Replace the fuel filter.
7. Contact an Authorized Service Dealer.
1. Reduce the ground speed.
2. Add oil to the crankcase.
3. Remove the obstruction from the
cooling fins and the air passages.
1. Adjust the tracking.
2. Adjust tire pressure in the drive tires.
3. Adjust the reverse indicator and the
speed-control linkage.
1. Tighten the bypass valves.
2. Change the belt.
3. Change the belt.
4. Replace the spring.
5. Add hydraulic fluid to reservoirs or let it
cool down.
1. Install new cutting blade(s).
2. Tighten the blade mounting bolt.
3. Tighten the engine mounting bolts.
4. Tighten the appropriate pulley.
5. Contact an Authorized Service Dealer.
6. Contact an Authorized Service Dealer.
7. Install new belt.
1. Sharpen the blade(s).
2. Install new cutting blade(s).
3. Level the mower deck from side-to-side
and front-to-rear.
4. Clean the underside of the mower.
5. Adjust the tire pressure in the drive
tires.
6. Position the spacers under hairpin
cotters.
7. Replace blades, spindles and (or)
check for damage to mower deck.
1. Check the belt tension or replace belt
2. Connect the PTO shaft.
3. Check the belt for damage. Install the
belt and check adjusting shafts and
belt guides for correct position.