Toro 74310 Setup Instructions
Z master 8000 series with 42in and 48in direct-collect cutting unit
Hide thumbs
Also See for 74310:
- Operator's manual (64 pages) ,
- Operator's manual (64 pages) ,
- Setup instructions (12 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
Z Master
with 42in and 48in Direct-Collect Cutting Unit
Model No. 74310—Serial No. 316000001 and Up
Model No. 74311TE—Serial No. 316000001 and Up
Model No. 74312—Serial No. 316000001 and Up
Model No. 74313—Serial No. 316000001 and Up
This product contains a chemical or chemicals known to the State of California to
The engine exhaust from this product contains chemicals known to the State of California
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
9
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
8000 Series Riding Mower
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
to cause cancer, birth defects, or other reproductive harm.
Description
No parts required
Rear caster wheel
Bolt (1/2 x 13 inches)
Locknut (1/2 inch)
Long guard
Guard
Bolt (1/4 x 1 inch)
Flat washer (1/4 inch)
Retainer nut (1/4 inch)
No parts required
No parts required
No parts required
Wing nut (1/4 inch)
No parts required
No parts required
Register at www.Toro.com.
WARNING
CALIFORNIA
Qty.
–
1
1
1
1
1
4
4
4
–
–
–
2
–
–
Form No. 3406-121 Rev A
Setup Instructions
Use
Open the crate.
Remove the machine from the crate.
Install the PTO shaft guards
(International machines only).
Check the tire pressure.
Check the engine-oil level.
Check the torque of the wheel lug nuts.
Install the battery.
Charge the battery.
Check the hydraulic Fluid.
Original Instructions (EN)
All Rights Reserved *3406-121* A
Printed in the USA.
Advertisement
Table of Contents
Related Manuals for Toro 74310
Summary of Contents for Toro 74310
-
Page 1: Loose Parts
® 8000 Series Riding Mower with 42in and 48in Direct-Collect Cutting Unit Model No. 74310—Serial No. 316000001 and Up Model No. 74311TE—Serial No. 316000001 and Up Model No. 74312—Serial No. 316000001 and Up Model No. 74313—Serial No. 316000001 and Up... -
Page 2: Opening The Crate
Procedure Description Qty. Number 2 general-purpose lithium-base or molybdenum-base grease. (Purchase 1 tube Check the machine for grease. separately.) Check the machine before delivery to – No parts required the customer (All machines). Operator's Manual Engine Owner's Manual Delivering the machine to the customer Registration card (All machines). - Page 3 6. Torque the bolt to 90.8 to 112.5 N∙m (67 to 83 ft-lb). 10. Place a plywood sheet (58.4 cm x 81.3 cm (23 inches x 32 inches)), or similar support, over the opening to provide support for the deck when the unit is driven off of the crate (Figure Figure 2...
- Page 4 Figure 6 3. Push the deck-locking pin 1. Deck lift handle g026151 in and rotate toward the Figure 8 front to lock 2. Rotate the deck-locking 1. Front caster 3. Plywood between the pin toward the rear and drive wheels pull outward to unlock 2.
- Page 5 2. Remove the bolt holding the rear frame to the crate (Figure 11). 3. Lift the front of the hopper up. Note: Use care when hoisting the machine to prevent damaging the hopper. 4. Using the hoist, lift the machine at the location shown Figure Figure 10 1.
- Page 6 Figure 13 Figure 12 1. Deck-support pin 3. Side-strut hardware 2. Strut between the 1. Lift points on each side of the seat deck-support pins Important: Ensure the mower deck is in the 21. With the deck locking pins pulled out in the unlock upright position before raising the front of the position, carefully lower the deck (Figure...
-
Page 7: Checking The Tire Pressure
Installing the PTO Shaft Guards International Machines Only Parts needed for this procedure: Long guard Guard Bolt (1/4 x 1 inch) Flat washer (1/4 inch) Retainer nut (1/4 inch) Figure 16 Procedure 3. Metal guards 1. Guard attached to the mower deck Note: This procedure is only for international machines. -
Page 8: Checking The Torque Of The Wheel Lug Nuts
WARNING If the ignition is in the On position there is potential for sparks and engagement of components. Sparks could cause an explosion or moving parts could Checking the Torque of the accidentally engage causing personal injury. Wheel Lug Nuts Be sure ignition switch is in the Off position before charging the battery. -
Page 9: Checking The Hydraulic Fluid
The machine is shipped with hydraulic oil in the reservoir. 1. Check and ensure the reservoir has hydraulic oil. Parts needed for this procedure: 2. If needed add Toro HYPR-OIL™ 500 hydraulic oil. Number 2 general-purpose lithium-base or 3. Run the machine for approximately 15 minutes to allow 1 tube molybdenum-base grease. - Page 10 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures. Initial Check Procedure Check the tire pressure.
- Page 11 Delivering the Machine to the Customer Parts needed for this procedure: Operator's Manual Engine Owner's Manual Registration card Operator-training material Procedure At delivery, fill in the model and serial number, complete the items listed in the following table, and initial each when finished. Model No.
- Page 12 Make sure that the customer receives the Operator's Manual, Engine Owner's Manual, Set Up Instructions, and operator training material. Make sure the customer knows the Parts Catalog is available at www.Toro.com. Assist the customer in loading the machine. Note: When you, the dealer representative, have finished delivering the machine to the customer, sign and date in the space provide below and keep a copy of this page for dealer records.