Toro 41086 Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Paint Sprayer
  5. 41086
  6. Operator's manual
Toro 41086 Operator's Manual

Toro 41086 Operator's Manual

Procontrol spray system turf sprayer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Form No. 3365-343 Rev A
ProControl Spray System
Multi-Pro
®
5600 and 5700-D Turf Sprayer
Model No. 41086—Serial No. 310000001 and Up
To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
Original Instructions (EN)

Advertisement

Table of Contents
loading

Related Manuals for Toro 41086

Summary of Contents for Toro 41086

  • Page 1 Form No. 3365-343 Rev A ProControl Spray System Multi-Pro ® 5600 and 5700-D Turf Sprayer Model No. 41086—Serial No. 310000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com. Original Instructions (EN)

  • Page 2: Table Of Contents

    Older only..........5 products, you are responsible for operating the product Installing the ProControlFor Model Year 2010 properly and safely. You may contact Toro directly at and Newer only..........6 www.Toro.com for product and accessory information, Product Overview ............9 help finding a dealer, or to register your product.

  • Page 3: Safety

    Safety Read and understand the contents of this manual before operating the console computer. • Keep this document with the Operator’s Manual for the Multi Pro ® 5600 or 5700-D Turf Sprayer. • It is very important that all who operate this equipment have ready access to these instructions at all times.

  • Page 4: Setup

    Setup Loose Parts Use the chart below to verify that all parts have been shipped. Description Qty. Grommet,large Carriage bolt (5/16 x 3/4 inch) Lock nut (5/16 inch) Computer console assembly Hand Knob Pivot bracket (2009 and older only) Hose barb fitting, 90 degree Hose, long Hose clamp Screw, flange head (1/4 x 3/4 inch)

  • Page 5: Installing The Procontrolfor Model Year 2009 And Older Only

    7. Secure the cables to the console computer by CAUTION rotating the locking rings. Many chemicals are hazardous and can cause 8. Attach the console computer to the mounting personal injury or environmental damage if you bracket and secure it with the 2 mounting knobs apply them improperly.

  • Page 6: Installing The Procontrolfor Model Year 2010 And Newer Only

    Installing the ProControl 4. Install a barbed fitting into the end of the longer supply hose section and secure it with a hose clamp For Model Year 2010 and next to the fitting body. Newer only. Important: Apply liquid soap to the barbed fitting to lubricate it.
  • Page 7 6. Plug the cables into their corresponding inputs on 3. Locate the 90 degree fitting and long hose in the rear of the console computer and secure the loose parts. Lightly lubricate the barb with a cables by rotating the locking rings. non-petroleum based lubricant, such as vegetable oil.
  • Page 8 13. Secure the shorter hose to the manifold and flowmeter respectively by sliding the hose clamps into positions over the barb and tightening. 14. Secure the flowmeter assembly to the flowmeter bracket with hose clamps. 15. Locate the spray system wiring harness routed to the boom valve manifold.

  • Page 9: Product Overview

    Product Overview 3. Install three bypass caps onto the all boom valves and secure them with the forks removed previously (Figure 11). G013304 Figure 12 1. Power switch 5. Function keys 2. Flow control switch 6. CE key 3. Display 7.
  • Page 10 SPEED Speed calibration number It enables you to verify that the vehicle distance readout is accurate. Enter 148 as a starting point for all Toro sprayers. METER Flowmeter calibration number Enter the number found on the flowmeter label or the tag on the flowmeter cable.

  • Page 11: Operation

    Clear Entry It clears a wrong entry; enables you to toggle between settings during initial programming; and enables you to select functions and settings. TOTAL Total area sprayed It monitors the total area until you clear it to zero. AREA TOTAL Total volume of material sprayed It monitors the volume of material sprayed until you clear it to zero.

  • Page 12: Programming The Console Computer

    Note: If you make a data entry error, reset the 4. Press the [Enter] key. console computer by turning the power switch to 5. Press the [Boom 2 Cal] key. the Off position and, while pressing and holding 6. Press the [Enter] key. the [CE] key, turning the power switch to the On position.
  • Page 13 New SPEED Cal number = 148 x 500/ Distance 2. Press the [Enter] key. readout 3. Enter the Valve Cal calibration number. 10. Enter the new Speed Cal number using the previous Note: The initial valve calibration number for procedure. Valve Cal is 023.

  • Page 14: Self-Testing The Console Computer

    Enter the time of day based on a 24-hour day. For Press the [Area/Hr] key. example, 1:30 p.m. is 13:30. You can also enter 0 to US, TI, TU, SP1, SP2, or SP3 measure elapsed time. Press and hold the [Self Test] key.Press the [Total Area] Note: This data is lost each time the power is turned key.

  • Page 15: Entering The Mode Sequence With The Data Lock Activated

    Entering the Mode Sequence Setting the Low Limit Flow Set with the Data Lock Activated Point and Low Limit Alarm 1. Press the key in which you wish to enter day. This is an optional feature. 2. Press the [Enter] key. If the actual volume per minute falls below this limit, the control valve stops closing, the alarm sounds, and the display flashes –LL–.

  • Page 16: Initially Field-Testing The System

    Note: The pump should increase the pressure until it reaches the desired rate if a Self Test speed has been entered. 13. Turn the Master Boom Control (foot) switch to the Off position. Note: The system stops the pump. 14. Turn the Agitation switch to the On position. Note: The system starts the pump and increases the pump speed until the pump reaches the preset agitation pressure.

  • Page 17: Maintenance

    Maintenance Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Clean the flowmeter. (More often when using wettable powders) Every 200 hours Cleaning the Flowmeter the hex stud on the bottom of the turbine hub by 1/16 of a turn until the turbine spins freely. Service Interval: Every 200 hours/Yearly (whichever comes first) (More often when using Calibrating the Flowmeter...

  • Page 18: Testing The Flowmeter Cable

    Corrected Meter Cal = (Meter Cal x Total Volume) / Amount of Water Corrected Meter Cal = (1660 x 103) /100 Corrected Meter Cal = 1710. Note: Repeat this procedure several times to confirm that the corrected Meter Cal number is accurate. Testing the Flowmeter Cable 1.

  • Page 19: Troubleshooting

    Troubleshooting Note: If the console computer malfunctions or needs repair, you can resume spraying in manual mode by unplugging the cables form the rear of the console computer. You can then control the system using the center console controls. Problem Possible Cause Corrective Action No display lights with the power on...
  • Page 20 Problem Possible Cause Corrective Action The rate is inaccurate or unstable 1. You incorrectly entered a number in the 1. Verify that all the numbers entered in console computer. the console computer are correct. 2. The wheel drive setting is not set to 2.

This manual is also suitable for:

Multi-pro 5700-dMulti-pro 5600

Table of Contents