Table of Contents
Advertisement
Quick Links
82 mm (3-1/4") MODEL Mi02
295
m m
I 1 1 518")
8 2 m m (3-114")
1
1
mm
(1/32"1
16,000
INSTRUCTION MANUAL
2 5
k g
( 5 5 lbsi
DOUBLE
INSULATION
SPEC IF I
CAT IONS
1
Planing depth
1
No
load speed
i
Overall
length
1
Net weight
(RPM)
Planing width
*
Manufacturer reserves the right t o change specifications w i t h o u t notice
* Note Specifications may differ from country t o country
Advertisement
Table of Contents
Related Manuals for Makita M102
Summary of Contents for Makita M102
- Page 1 INSTRUCTION MANUAL SPEC IF I CAT IONS Planing depth Planing width 8 2 m m (3-114") (1/32"1 Manufacturer reserves the right t o change specifications w i t h o u t notice * Note Specifications may differ from country t o country 82 mm (3-1/4") MODEL Mi02 length load speed...
- Page 2 SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
- Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed f r o m tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don‘t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. OUTDOOR USE EXTENSION CORDS.
- Page 4 Do not leave the tool running. Operate the tool only when hand-held. 1 4 . When leaving the planer, switch off and set it with the front base u p o n a wooden block, so that the blades do n o t contact anything.
- Page 5 To check for proper blade pro- trusion, rotate the drum in the cutting direction by turning the planer drive belt while lightly holding the triangular rule flush against the rear base. The triangular rule flush against the rear base.
- Page 6 Follow the same installation pro- cedures covered in "Removing mini planer blades". Adjusting d a t e plate M i n i planer blade installing Heel of adjusting plate Groove...
- Page 7 For the correct planer blade setting Your planing surface will end up rough and uneven, unless the blade is set properly and securely. The blade must parallel to the surface of the reat base. Below are some examples of proper and improper settings.
- Page 8 The speed and depth of cut determine the kind of finish. The power planer keeps cutting will not result in jamming by chips. For rough cutting, the depth of cut can be increased, while for reduce the depth of cut and advance the tool more slowly.
- Page 9 To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance of adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. length of...
- Page 10 Planer blade Part 793209-0 Dust bag assembly Part No. 122269-7 Blade gauge No. 41 Part 11 75-4 w i t h your Makita tool specified in this Guide rule Part No. 191455-1 Screwdriver Part No. 783002-8 Socket wrench Part 798145-3...
- Page 11 Sep -17 -'87 mm (3-1/4") POWER PLANER Model MI02 Note The switch, noise suppressor and other part configurations may differ from country to country...
- Page 12 10 the In no event shall Makita be liable for any indirect incidental or consequential damages from the sale use of the product This disclaimer applies both during and after the term...