Cisco C20 TelePresence System Administrator's Manual page 96

Hide thumbs Also See for C20 TelePresence System:
Table of Contents

Advertisement

Cisco TelePresence System Quick Set C20 and Profiles using C20
Contents
Video SelfviewDefault FullscreenMode
Determine if the main video source (self view) shall be shown in full screen or as a small
picture-in-picture (PiP) after a call. The setting only takes effect when self view is switched on
(see the Video SelfviewDefault Mode setting).
Requires user role: ADMIN
Value space: <Off/Current/On>
Off: Self view will be shown as a PiP.
Current: The size of the self view picture will be kept unchanged when leaving a call, i.e. if it
was a PiP during the call, it remains a PiP after the call; if it was fullscreen during the call, it
remains fullscreen after the call.
On: The self view picture will be shown in fullscreen.
Video SelfviewDefault FullscreenMode: Current
Example:
Video SelfviewDefault PIPPosition
Determine the position on screen of the small self view picture-in-picture (PiP) after a call. The
setting only takes effect when self view is switched on (see the Video SelfviewDefault Mode
setting) and fullscreen view is switched off (see the Video SelfviewDefault FullscreenMode
setting).
This setting obsoletes the Video SelfviewPosition setting as from TC6.0.
Requires user role: ADMIN
Value space: <Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/LowerLeft/
LowerRight >
Current: The position of the self view PiP will be kept unchanged when leaving a call.
UpperLeft: The self view PiP will appear in the upper left corner of the screen.
UpperCenter: The self view PiP will appear in the upper center position.
UpperRight: The self view PiP will appear in the upper right corner of the screen.
CenterLeft: The self view PiP will appear in the center left position.
CentreRight: The self view PiP will appear in the center right position.
LowerLeft: The self view PiP will appear in the lower left corner of the screen.
LowerRight: The self view PiP will appear in the lower right corner of the screen.
Video SelfviewDefault PIPPosition: Current
Example:
D14637.10 Profile C20 and Quick Set C20 Administrator Guide TC6.1, APRIL 2013.
Introduction
Web interface
System settings
System settings
Video SelfviewDefault OnMonitorRole
Determine which monitor/output to display the main video source (self view) on after a call.
The value reflects the monitor roles set for the different outputs in the Video Output HDMI
MonitorRole settings.
The setting applies both when self view is displayed in full screen, and when it is displayed as
picture-in-picture (PiP), but only if the Video Monitors setting is set to Dual.
Requires user role: ADMIN
Value space: <First/Second/Current>
First: The self view picture will be shown on outputs with the Video Output HDMI MonitorRole
set to First.
Second: The self view picture will be shown on outputs with the Video Output HDMI
MonitorRole set to Second.
Current: When leaving the call, the self view picture will be kept on the same output as
during the call.
Video SelfviewDefault OnMonitorRole: Current
Example:
Video CamCtrlPip CallSetup Mode
This setting is used to switch on self view for a short while when setting up a call. The Video
CamCtrlPip CallSetup Duration setting determines for how long it remains on. This applies when
self view in general is switched off.
Requires user role: ADMIN
Value space: <Off/On>
Off: Self view is not shown automatically during call setup.
On: Self view is shown automatically during call setup.
Video CamCtrlPip CallSetup Mode: Off
Example:
Video CamCtrlPip CallSetup Duration
This setting only has an effect when the Video CamCtrlPip CallSetup Mode setting is switched
On. In this case, the number of seconds set here determines for how long self view is shown
before it is automatically switched off.
Requires user role: ADMIN
Value space: <1..60>
Range: Choose for how long self view remains on. The valid range is between 1 and 60
seconds.
Video CamCtrlPip CallSetup Duration: 10
Example:
www.cisco.com — Copyright © 2010-2013 Cisco Systems, Inc. All rights reserved.
96
Administrator Guide
Setting passwords
Appendices

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Telepresence profiles c20

Table of Contents