Direct Button Operation; Changing Channels; Changing Volume; Mute - Sharp Aquas LC-52LE920UN Operation Manual

Direct Button Operation
MUTE
•
OPTION SLEEP
~~~~
FREEZE
CJ _
CC AV MODE VIEW MODE fLASHBACK
MUTE
Mutes the current sound output.
Press
MUTE.
• "C@"
will be displayed on the screen for 30 minutes, and
the sound is silenced.
mm
• Within 30 minutes of pressing
MUTE,
mute can be
canceled by pressing
VOL
+ / -
or
MUTE.
• Mute will be canceled after 30 minutes have passed.
However, the TV will not suddenly output a loud sound as
the volume level is set to 0 automatically.
Sleep Timer
Changing Channels
You can change channels in several ways.
Method 1
Using
CH/\lV
on Hle remote control unit or on the
TV.
Method 2
Using remote control buttons
0-9, • (DOT).
Examples:
To select a 1 or 2-digit channel number (eo go, Channel 5):
Press 5 -----7
ENT.
To select a 3-digit channel number (e. g., Channel 115):
Press 1 -----7 1 -----7 5 -----7
ENT.
To select a 4-digit channel number (eo g., Channel 22.1):
Press 2 -----7 2 ---"7 •
(DOT) -----7 1 -----7ENT.
Method 3
Selecting the program from CH List.
1
Press
INPUT
on the remote control unit.
• The Input list displays.
2
Press ....
/~
to select "AIR" or "CABLE".
• The Channel list displays.
3
Press
J;./T
to select the desired channel, and then
press
ENTER.
mm
• When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
• When you enter 0-9 only, channel selection will be made if
there is no operation within a few seconds.
• If you push "0" by itself, nothing will happen.
• Complete the above steps within a few seconds.
• When you enter 0-9 and • (DOT), channel selection will be
made if there is no operation within a few seconds.
Changing Volume
You can change the volume by pressing
VOL
+ / -
on
the
TV
or on the remote control unit.
• To increase the volume, press VOL+.
• To decrease the volume, press
VOL - .
• _ _
"~~"""dt$'';;lP''
g
Audio status
mm
• See page 30 for details on the Output Select function.
Allows you to set a time when the
TV
automaticaJiy
switches to standby.
Press
SLEEP.
• The remaining time displays when the sleep timer has been set.
• Each time you press
SLEEP,
the remaining time switches
as shown below.
Off ... 30 ... 60 ... 90 ... 120
t ,
• When set, the time automatically starts counting down.
• If you want to adjust the sleep timer, you can press SLEEP
twice then change the time setting.
• When it is 5 minutes before the time expires, the remaining
time will start to keep appearing every minute.
mm
• Select "Off" by pressing SLEEP to cancel the sleep timer,
• The 1V will enter standby when the remaining time
reache~,
0,
FLASHBACK
Press
FLASHBACK
to switch to the previously tuned
channel.
• Press
FLASHBACK
again to switch back to the currently
tuned channel.
mm
• FLASHBACK
will not work if no channel has been
changed after the TV is turned on.
FREEZE .
Allows you to capture and freeze a moving image that
you are watching.
Press
FREEZE.
• A moving image is captured.
• Press FREEZE again to cancel the function.
mm
• When this function is not available, "No displaying still
image available." will display.
• The still image automatically goes out after 30 minutE'S.
• If you are using the freeze function and a broadcast
activates the V-CHIP BLOCK, the freeze function will be
canceled and a V-CHIP BLOCK message will appear.
• You can have the same settings by choosing "Freeze" on
the menu items. (See page 29.)
@-19