The Video Settings - Cisco EX90 Administrator's Manual

Cisco TelePresence System EX90/EX60
Contents

The Video settings

Video Selfview
Determine if the main video source (selfview) shall be displayed on screen.
Requires user role: ADMIN
Value space: <On/Off>
On: Set to On when you want selfview to be displayed on screen.
Off: Set to Off when you do not want selfview to be displayed on screen.
Example: Video Selfview: On
Video WallPaper
Determine which background picture to show on the touch screen controller and main screen when
idle. It is recommended to use Wallpaper01 to Wallpaper12.
Requires user role: USER
Value space: <None/Growing/Summersky/Custom/Wallpaper01/Wallpaper02/Wallpaper03/
Wallpaper04/Wallpaper05/Wallpaper06/Wallpaper07/Wallpaper08/Wallpaper09/Wallpaper10/
Wallpaper11/Wallpaper12/>
Wallpaper01 to Wallpaper12: Select one of the predefined wallpapers to be displayed on the
main screen and on the touch screen. The wallpaper will be shown on both screens.
None: No wallpaper will be displayed on the main screen. Note: When you change the wallpaper
on the touch screen, it will also set the wallpaper for the main screen.
Summersky, Growing: Select one of the predefined wallpapers to be displayed on the main
screen. It will not be displayed on the touch screen. Note: When you change the wallpaper on the
touch screen, it will also change the wallpaper for the main screen.
Custom: The custom wallpaper will only show on the main screen, not the touch screen. It must
be uploaded to the codec from the web interface before selecting Custom.
1) On the video system: Find the IP address of the codec. Open the menu on screen and go to
Home > Settings > System information to find the IP Address.
2) On your computer: Open a web browser and enter the IP address of the codec. Select
"Wallpaper" from the menu, browse for the file, and press the "Upload" button.
3) On the web interface: Log in and go to Advanced Configuration > Video > Wallpaper and
select Custom. Give it a few seconds to display the new picture. If the picture does not show,
toggle once between "None" and "Custom" wallpaper to make the change take effect. Note:
When you change the wallpaper on the touch screen, it will also change the wallpaper for the main
screen.
Example: Video Wallpaper: Wallpaper01
Video MainVideoSource
Not applicable in this version.
D14726.03 Cisco TelePresence System EX90-EX60 Administrator Guide TC4.0, December 2010.
Copyright © 2010 Cisco Systems, Inc. All rights reserved.
Introduction Using the web interface Advanced configuration
The Video settings,
cont...
Video defaultPresentationSource
Note: EX90 has Video Input Source [1..3] and EX60 has Video Input Source [1..2].
Define which video input source shall be used as the default presentation source (e.g. when you tap
View followed by Present on the touch screen controller). The input source is configured to a video
input connector.
Requires user role: USER
Value space: <1..3>/<1..2>
Range: Select the video input source to be used as the presentation source.
Example: Video DefaultPresentationSource: 1
Video Monitors
Set the monitor layout mode.
Requires user role: ADMIN
Value space: <Single/Dual/DualPresentationOnly>
Single: The same layout is shown on all monitors.
Dual: The layout is distributed on two monitors.
DualPresentationOnly: All participants in the call will be shown on the first monitr, while the
presentation (if any) will be shown on the second monitor.
Example: Video Monitors: Single
Video Input Source [1..3]/[1..2] Name
Note: EX90 has Video Input Source [1..3] and EX60 has Video Input Source [1..2].
Enter a name for the video input source.
Requires user role: ADMIN
Value space: <S: 0, 50>
Format: String with a maximum of 50 characters.
Example: Video Input Source 1 Name: ""
Video Input Source 1 Connector
Note: EX90 has Video Input Source [1..3]. EX60 has Video Input Source [1..2].
Select which video input connector to be active on video input source 1.
Requires user role: ADMIN
Value space: <HDMI>/<DVI>
HDMI (EX90): Select HDMI when you want to use the HDMI as the video input source 1.
DVI (EX60): Select DVI when you want to use the DVI as the video input source 1.
Example: Video Input Source 1 Connector: HDMI
47
Administrator guide
Appendices
www.cisco.com