Makita BGA402 Instruction Manual
Cordless angle grinder
Hide thumbs
Also See for BGA402:
- Instruction manuals (80 pages) ,
- Instruction manual (80 pages) ,
- Instruction manual (21 pages)
Related Manuals for Makita BGA402
Summary of Contents for Makita BGA402
- Page 1 INSTRUCTION MANUAL Cordless Angle Grinder BGA402 BGA450 BGA452 007214 IMPORTANT: Read Before Using.
-
Page 2: Specifications
ENGLISH (Original instructions) SPECIFICATIONS Model BGA402 BGA450 BGA452 Wheel diameter 100 mm 115 mm Spindle thread Rated speed (n) / No load speed (n 10000 (min Overall length 317 mm Net weight 2.2 kg 2.2 kg 2.3 kg Rated voltage D.C. - Page 3 If operating a power tool in a damp location is 20. Store idle power tools out of the reach of unavoidable, use a ground fault circuit children and do not allow persons unfamiliar interrupter (GFCI) protected supply. Use of an with the power tool or these instructions to GFCI reduces the risk of electric shock.
-
Page 4: Grinder Safety Warnings
GEB033-4 capable stopping small abrasive workpiece fragments. The eye protection must GRINDER SAFETY WARNINGS be capable of stopping flying debris generated by Safety Warnings Common for Grinding, Sanding, various operations . The dust mask or respirator Wire Brushing, or Abrasive Cutting-Off Operations: must be capable of filtrating particles generated This power tool is intended to function as a by your operation. - Page 5 point of pinching. Abrasive wheels may also break under Additional Safety Warnings Specific for Abrasive these conditions. Cutting-Off Operations: Kickback is the result of power tool misuse and/or a) Do not “jam” the cut-off wheel or apply incorrect operating procedures or conditions and can be excessive pressure.
- Page 6 Additional safety warnings: disconnect the tool from the mains supply 17. When using depressed centre grinding wheels, ( use non metallic objects ) and avoid be sure to use only fiberglass-reinforced damaging internal parts. wheels. 37. When use cut-off wheel, always work with the dust collecting wheel guard required by 18.
-
Page 7: Functional Description
Be careful not to drop or strike battery. Shaft lock Do not use dropped or struck battery. 1. Shaft lock SAVE THESE INSTRUCTIONS. Tips for maintaining maximum battery life Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power. - Page 8 indication lamp has broken. Installing or removing wheel guard (For − Overload protection depressed center wheel , multi disc / abrasive − When the tool is overloaded, the indication cut-off wheel , diamond wheel) lamp lights up. When the load on the tool is For tool with locking screw type wheel guard reduced, the lamp goes out.
-
Page 9: Operation
To tighten the lock nut, press the shaft lock firmly so that Grinding and sanding operation the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. 1. Lock nut wrench 2. Shaft lock 007221 ALWAYS hold the tool firmly with one hand on housing 007220 and the other on the side handle. -
Page 10: Maintenance
100 mm (4") Abrasive cut-off wheel Diamond wheel Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more 16 mm (5/8") 16 mm (5/8") 20 mm (13/16") 20 mm (13/16") 1. - Page 11 Replacing carbon brushes attachment for its stated purpose. If you need any assistance for more details regarding 1. Limit mark these accessories, ask your local Makita Service Center. Wheel guard (Wheel cover) For depressed center • wheel / Multi disc Wheel guard (Wheel cover) For abrasive cut-off •...
- Page 12 Makita Corporation www.makita.com 884662D0...