Additional Safety Rules For Tool - Makita BLS713 Instruction Manual

9. Connect dust extraction equipment.
If devices are provided for the connection of dust
extraction and collection facilities ensure these are
connected and properly used.
10. Secure the work.
Use clamps or a vice to hold the work. It is safer
than using your hand and it frees both hands to
operate the tool.
11. Do not overreach.
Keep proper footing and balance at all times.
12. Maintain tools with care.
Keep cutting tools sharp and clean for better and
safer performance.
lubrication and changing accessories. Inspect tool
periodically and if damaged have repaired by an
authorized service facility. Keep handles dry, clean
and free from oil and grease.
13. Disconnect tools.
Where the design permits, disconnect the tool
from its battery pack when not in use, before
servicing and when changing accessories such as
blades, bits and cutters.
14. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning it on.
15. Avoid unintentional starting.
Do not carry the tool with a finger on the switch.
16. Stay alert.
Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
17. Check damaged parts.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
determine that it will operate properly and perform
its intended function. Check for alignment of
moving parts, free running of moving parts,
breakage of parts, mounting and any other
conditions that may affect its operation. A guard or
other part that is damaged should be properly
repaired or replaced by an authorized service
center unless
instruction manual. Have defective switches
replaced by an authorized service facility. Do not
use the tool if the switch does not turn it on and off.
18. Warning.
The use of any accessory or attachment, other
than recommended in this instruction manual or
the catalog, may present a risk of personal injury.
Ensure that the battery pack is correct for the tool.
Ensure that the outside surface of battery pack or
tool is clean and dry before plugging into charger.
Ensure that batteries are charged using the
correct charger
manufacturer. Incorrect use may result in a risk of
Follow instructions
otherwise indicated
recommended by
electric shock, overheating or leakage of corrosive
liquid from the battery.
19. Have your tool repaired by a qualified person.
This tool is constructed in accordance with the
relevant safety requirements. Repairs should only
be carried out by qualified persons using original
spare parts, otherwise this may result in
considerable danger to the user.
20. Disposal of battery.
Ensure battery is disposed of safely as instructed
by the manufacturer.
for
ADDITIONAL SAFETY RULES
FOR TOOL
1. Wear eye protection.
2. Keep hands out of path of saw blade. Avoid
contact with any coasting blade. It can still
cause severe injury.
3. Do not operate saw without guards in place.
Check blade guard for proper closing before
each use. Do not operate saw if blade guard
does not move freely and close instantly.
Never clamp or tie the blade guard into the
open position.
4. Do not perform any operation freehand. The
workpiece must be secured firmly against the turn
base and guide fence with the vise during all
operations. Never use your hand to secure the
workpiece.
5. Never reach around saw blade.
6. Turn off tool and wait for saw blade to stop
before
settings.
7. Remove the battery cartridge before changing
blade or servicing.
8. Always secure all moving portions before
carrying the tool.
9. Stopper pin which locks the cutter head down
is for carrying and storage purposes only and
not for any cutting operations.
in this
10. Do not use the tool in the presence of
flammable liquids or gases. The electrical
operation of the tool could create an explosion and
fire when exposed to flammable liquids or gases.
11. Check the blade carefully for cracks or
damage before operation.
Replace
immediately.
12. Use only flanges specified for this tool.
13. Be careful not to damage the arbor, flanges
(especially the installing surface) or bolt.
Damage to these parts could result in blade
the
breakage.
4
moving workpiece
cracked or damaged
ENB118-2
or changing
blade