Makita 3707 Instruction Manual
Hide thumbs
Also See for 3707:
- Instruction manual (57 pages) ,
- Specifications (2 pages) ,
- Instruction manual (13 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Advertisement
Table of Contents
Related Manuals for Makita 3707
Summary of Contents for Makita 3707
- Page 1 Trimmer MODEL 3707 MODEL 3707F MODEL 3707FC 004548 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
-
Page 2: Specifications
European Standard and can, therefore, also be used from sockets Yasuhiko Kanzaki CE 2005 without earth wire. Director MAKITA INTERNATIONAL EUROPE LTD. Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD, ENGLAND Responsible manufacturer: Makita Corporation Anjo Aichi Japan... -
Page 3: General Safety Rules
GENERAL SAFETY RULES GEA001-3 WARNING: Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery- operated (cordless) power tool. -
Page 4: Specific Safety Rules
19. Store idle power tools out of the reach of chil- Avoid cutting nails. Inspect for and remove all dren and do not allow persons unfamiliar with nails from the workpiece before operation. the power tool or these instructions to operate Hold the tool firmly. -
Page 5: Functional Description
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Adjusting bit protrusion 001698 To adjust the bit protrusion, loosen the lever and move the tool base up or down as desired by turning the adjusting roller. -
Page 6: Operation
ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing or removing trimmer bit 001700 CAUTION: • Do not tighten the collet nut without inserting a bit, or the collet cone will break. - Page 7 Templet guide 001703 The templet guide provides a sleeve through which the bit passes, allowing use of the trimmer with templet patterns. Loosen the screws and remove the base protector. Place the templet guide on 001704 the base and replace the base protector. Then secure the base protector by tightening the screws.
- Page 8 Attach the guide plate to the straight guide with the bolt, the wave washer, the 001990 flat washer and the wing nut. 1. Bolt 2. Guide plate 3. Straight guide 4. Flat washer 5. Wave washer 6. Wing nut Attach the straight guide with the clamp screw (A). Loosen the wing nut on the 001708 straight guide and adjust the distance between the bit and the straight guide.
- Page 9 Circular work 001993 Circular work may be accomplished if you assemble the straight guide and guide plate as shown in the figures. Min. and max. radius of circles to be cut (distance between the center of circle and the center of bit) are as follows: Min.: 70 mm Max.: 221 mm For cutting circles between 70 mm and 121 mm in radius.
-
Page 10: Maintenance
Trimmer guide 001713 Trimming, curved cuts in veneers for furniture and the like can be done easily with the trimmer guide. The guide roller rides the curve and assures a fine cut. Install the trimmer guide on the tool base with the clamp screw (A). Loosen the 001714 clamp screw (B) and adjust the distance between the bit and the trimmer guide by turning the adjusting screw (1 mm per turn). - Page 11 CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
- Page 12 “V”Grooving bit 005118 006454 90˚ 1/4" Drill point flush trimming bit 005120 006487 1/4" Drill point double flush trimming bit 005121 006488 1/4" Corner rounding bit 005125 006489 1/4" 1/4" Chamfering bit 005126 006462 30˚ 30˚ 30˚ E 1/4" 45˚ 45˚...
- Page 13 Cove beading bit 005129 006464 1/4" 1/4" Ball bearing flush trimming bit 005130 006465 1/4" Ball bearing corner rounding bit 005131 006466 1/4" 1/4" Ball bearing chamfering bit 005132 006467 45˚ 45˚ 45˚ E 1/4" 60˚ 60˚ 60˚ E 1/4" Ball bearing beading bit 005133 006468...
- Page 14 Ball bearing cove beading bit 005134 006469 1/4" 1/4" Ball bearing roman ogee bit 005135 006470 1/4" 1/4"...
- Page 15 Memo...
- Page 16 Makita Corporation Anjo, Aichi, Japan 884437C223...