Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Grizzly H5626/7
Summary of Contents for Grizzly H5626/7
- Page 1 MODEL H5626/7 INSTRUCTION MANUAL Model H5626 Model H5627 COPYRIGHT © SEPTEMBER, 2003 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN TAIWAN...
-
Page 2: Safety Instructions For Pneumatic Tools
For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbols is described below. - Page 3 Safety Instructions For Pneumatic Tools 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts.
- Page 4 Basic Stapler Safety In addition to the rules stated in the previ- ous section, and those in the warning boxes throughout this manual, please observe the following safety tips for your new stapler: READ THIS ENTIRE MANUAL BEFORE OPERATING THE STA- PLER.
- Page 5 Commentary We are proud to offer the Grizzly Model H5626/H5627 Upholstery Stapler. This model is part of a growing Grizzly family of fine power tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoy- able operation and proof of Grizzly’s com-...
-
Page 6: Compressed Air System
Check the current Grizzly cata- log for availability of this unit. If you plan on installing a filter/lubricator/regulator unit in... -
Page 7: Operation
Loading Stapler To load your stapler: Disconnect the air supply from the stapler! Push the magazine latch in the direc- tion shown in Figure 2. Figure 2. Releasing magazine latch. OPERATION Pull back the magazine cover until it stops. Point the stapler up and insert a stick of staples into the magazine as shown in Figure 3. - Page 8 Operating Stapler If you have not read the safety instruc- tions in this manual, do not operate the stapler. Every time you operate your stapler, place one drop of the included oil into the quick connect fitting where the stapler connects to the air supply.
-
Page 9: Speed Adjustment
Speed Adjustment The Model H5627 features staple firing speeds from .5 to 16 staples per second. To adjust the staple firing speed: Disconnect the stapler from the air supply! Release the speed adjustment lock by holding the speed adjustment screw in place with a screwdriver while rotat- ing the speed adjustment lock counter clockwise. - Page 10 Cleaning Stapler Use a good solvent to clean the nose assembly of the stapler. Always be sure that the stapler is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the sta- pler;...
- Page 11 Replacing Pistons/O-Rings If you use your stapler day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or pis- ton shaft becomes worn out. Always disconnect air from stapler...
-
Page 12: Maintenance Notes
MAINTENANCE NOTES H5626/H5627 Upholstery Stapler... - Page 13 H5626 PART BREAKDOWN H5626/H5627 Upholstery Stapler...
- Page 14 PART # DESCRIPTION 01 PSB95M CAP SCR M5-.8 X 30 03 PH5626003 CAP COVER 04 PH5626004 SPRING 05 PH5626005 SEAL 06 PH5626006 CAP 07 PH5626007 O-RING 08 PH5626008 HEAD VALVE ASM. 09 PH5626009 O-RING 11 PH5626011 O-RING 12 PH5626012 COLLAR 13 PH5626013 O-RING 14 PH5626014 DRIVER ASSEMBLY 18 PH5626018 CYLINDER...
- Page 15 H5627 PART BREAKDOWN H5626/H5627 Upholstery Stapler...
- Page 16 PART # DESCRIPTION 01 PH5627001 CAP 02 PH5627002 O-RING 03 PH5627003 CYL. PRESS RING 04 PH5627004 O-RING 05 PH5627005 CYLINDER 06 PH5627006 O-RING 07 PH5627007 O-RING 08 PH5627008 DRIVER ASSEMBLY 09 PH5627009 BUMPER 10 PH5627010 COLLAR 11 PH5627011 O-RING 12 PH5627012 VALVE 13 PH5627013 VALVE PLUNGER 14 PH5627014 O-RING 15 PH5627015 O-RING...
-
Page 17: Troubleshooting
TROUBLESHOOTING PROBLEM Air leaking at trigger valve area. Air leaking between hous- ing and hose. Air leaking between hous- ing and cap assembly. Tool skips staples while discharging. Tool runs slowly or has a loss of power. Fasteners frequently jam the stapler. -
Page 18: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. -
Page 19: Warranty Card
14. Do you think your purchase represents good value? 15. Would you recommend Grizzly to a friend? 16. Would you allow us to use your name as a refer- ence for Grizzly customers in your area? Note: We never use names more than three times. 17.Comments:________________________________... - Page 20 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...