Grizzly H2909 Instruction Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Staple Gun
  5. H2909
  6. Instruction manual
Grizzly H2909 Instruction Manual

Grizzly H2909 Instruction Manual

18 gauge stapler kit
Hide thumbs Also See for H2909:
Table of Contents

Advertisement

Quick Links

Download this manual
18 GAUGE STAPLER KIT
MODEL H2909
INSTRUCTION MANUAL
COPYRIGHT © JANUARY, 2002 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN

Advertisement

Table of Contents
loading

Related Manuals for Grizzly H2909

Summary of Contents for Grizzly H2909

  • Page 1 INSTRUCTION MANUAL COPYRIGHT © JANUARY, 2002 BY GRIZZLY INDUSTRIAL, INC. 1821 VALENCIA ST., BELLINGHAM, WA 98227 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN TAIWAN...

  • Page 2: Safety Instructions For Power Tools

    For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbols is described below.
  • Page 3 14. DO NOT OVERREACH. Keep proper footing and balance at all times. H2909 18 Gauge Stapler Kit 15. MAINTAIN TOOLS WITH CARE. 16. DISCONNECT TOOLS before ser- 17. REDUCE THE RISK OF UNINTEN- 18.
  • Page 4 Use this tool with respect and caution to lessen the possibility of operator or bystander injury. Ignoring this warn- ing may result in serious personal injury. H2909 18 Gauge Stapler Kit American National...
  • Page 5 We are pleased to provide this manual with the Model H2909. It was written to encourage safety considerations and guide you through general operating pro- cedures and maintenance. This manual represents our effort to produce the best documentation possible.

  • Page 6: Compressed Air System

    Compressed Air System The Model H2909 is designed to be oper- ated at 60-100 psi. Do not exceed the maximum operating pressure for your model. Before you use your new stapler, install the ⁄ " quick connect fitting that comes with the stapler.

  • Page 7: Operation

    Figure 2. Make sure that the point- ed ends of the staples point in the same direction as the stapler nose piece. Figure 2. Loading staples into stapler. H2909 18 Gauge Stapler Kit OPERATION Push the magazine cover forward until the magazine latch locks in place.

  • Page 8: Clearing Jammed Staples

    The jammed staple should now be visible; remove it from the discharge area with needle nose pliers. Replace the staples. Push the maga- zine closed and snap the quick release latch back into operating posi- tion. H2909 18 Gauge Stapler Kit...
  • Page 9 As mentioned before, the best option is to install a filter/lubricator/regulator unit such as the Grizzly Model H2333 in your air line. Figure 5. Lubricating stapler via air inlet. H2909 18 Gauge Stapler Kit...
  • Page 10 Replacing Pistons/O-Rings If you use your stapler day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or pis- ton shaft becomes worn out. To replace a...
  • Page 11 H2909 PART BREAKDOWN H2909 18 Gauge Stapler Kit...
  • Page 12 PH2909049 MAGAZINE PH2909050 BRACKET PH2909051 CAP SCREW PH2909052 SHAFT STAPLE GUIDE UNIT PH2909053A END CORE PH2909054A PH2909055 UM HD BOLT PH2909056 PUSHER PH2909057 SLIDE BLOCK PH2909058 SPRING PH2909059 ROD PH2909060 SET BLOCK PH2909061 TAIL COVER H2909 18 Gauge Stapler Kit...

  • Page 13: Troubleshooting

    Tool runs slowly or has a loss of power. Fasteners frequently jam the stapler. Stapler does not fire. H2909 18 Gauge Stapler Kit CAUSE 1. O-rings in trigger valve housing are damaged. 1. Loose screws in housing. 2. Damaged O-ring.

  • Page 14: Warranty And Returns

    WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance.

  • Page 15: Warranty Card

    14. Do you think your purchase represents good value? 15. Would you recommend Grizzly to a friend? 16. Would you allow us to use your name as a refer- ence for Grizzly customers in your area? Note: We never use names more than three times. 17.Comments:________________________________...
  • Page 16 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...

Table of Contents