For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbols is described below.
Page 3
Safety Instructions For Pneumatic Tools 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neck- ties, rings, bracelets, or other jewel- ry which may get caught in moving parts.
Page 4
DO NOT USE A CHECK VALVE OR ANY OTHER FITTING that allows air to remain in the tool. G6044/G6772 16 Gauge Stapler Kit Operating this stapler can propel objects into the air, causing immedi- ate eye damage. To protect yourself,...
Page 5
Commentary We are proud to offer the Grizzly Model G6044/G6772 16 Gauge Stapler. This model is part of a growing Grizzly family of fine power tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoy- able operation and proof of Grizzly’s com-...
Compressed Air System The Model G6044/G6772 is designed to be operated at 80-120 psi. Do not exceed the maximum operating pressure! Before you use your new stapler, regulate the air pressure on your air compressor to barely over the minimum psi for your model.
Gauge: Length: Width: Capacity: 140 Staples Single/Bump Fire Mode The Model G6044/G6772 is equipped with a single/bump fire trigger. To select single or bump fire operation: Disconnect the air supply from the stapler! Locate the hex nut that secures the safety yoke mechanism to the trigger housing.
Page 8
Figure 4.) Besides damaging your workpiece, deflection can cause injury if your free G6044/G6772 16 Gauge Stapler Kit Figure 4. Example of staple deflection. hand is securing the workpiece in the location that the staple deflects.
Replace the quick release latch. Place undamaged staples back on the mag- azine and engage the pusher. Quick Release Latch Driver Guide Cover Figure 5. Removing guide cover. G6044/G6772 16 Gauge Stapler Kit...
Page 10
As mentioned before, the best option is to install a filter/lubricator/regulator unit such as the Grizzly Model H2333 in your air line. Figure 6. Lubricating stapler via air inlet. NOTICE Too much oil in the stapler will ruin...
Page 11
Replacing Pistons/O-Rings If you use your stapler day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or pis- ton shaft becomes worn out. To replace a...
1. Staple is jammed in mag- azine or discharge area. 2. Piston shaft is damaged. 3. Air pressure too low. G6044/G6772 16 Gauge Stapler Kit ACTION 1. O-rings must be replaced & operation of safety yoke must be checked.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance.
14. Do you think your purchase represents good value? 15. Would you recommend Grizzly to a friend? 16. Would you allow us to use your name as a refer- ence for Grizzly customers in your area? Note: We never use names more than three times. 17.Comments:________________________________...
Page 20
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...