Table of Contents
Related Manuals for Makita 9300
Summary of Contents for Makita 9300
- Page 1 Bench Grinder 125 mm (5") MODEL 9300 INSTRUCTION MANUAL SPEC IF CAT I 0 N Wheel size speed Overall length Net weight load Manufacturer reserves the right t o change specifications without notice. Note: Specifications may differ from country t o country.
-
Page 2: General Safety Precautions
For Your Own Safety Read Instruction Manual Before Operating BENCH GRINDER GENERAL SAFETY PRECAUTIONS (For All Tools) 1. KNOW YOUR POWER TOOL. Read the owner's manual carefully. Learn the tools applications and limitations, as well as the specific potential hazards peculiar t o 2. - Page 3 USE RECOMMENDED ACCESSORIES. Consult the owner's manual for recommended accessories. The use of improper accessories may cause risk of injury t o persons. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. CHECK DAMAGED PARTS.
-
Page 4: Grounding Instructions
GROUNDING INSTRUCTIONS ALL GROUNDED, CORD-CONNECTED TOOLS: In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current t o reduce the risk of electric shock. This tool is equipped with an electric cord hav- ing an equipment-grounding conductor and a grounding plug. -
Page 5: Additional Safety Rules For Bench Grinder
Do not strike or drop the wheel. Use only the shaft, flanges, nuts and other installing parts specified by Makita. Handle them carefully and remove any foreign matter adhering to them. 5. Always wear safety goggles when grinding. Also wear a face mask if there is much dust. - Page 6 14. Adjust tool rests so they are within 1 m m (1132") m m (118") of the grinding wheel. Height of tool rests should be so that are level with the middle (center) of the wheels. Always keep the clearance between the face of a straight wheel and the adjust plate less than 1.6 m m (1116").
-
Page 7: Names Of Parts
NAMES OF PARTS Shaft lock wheel Grinding Thumb screw C BEFORE USE 1. The eyeshields are packed together with the bench grinder. Always install the eyeshields before operation (see explan- ' \ \ Eyeshleld atory figure). 2. Fit eyeshields in between wheel cover and adjust plate (fitting small screws into installation holes on eyeshields). -
Page 8: How To Use
HOW TO USE Keep the space between the adjust plate Screw and grinding wheel under 1.6 mm (1/16"). Screw in securely the (+) P. H. screws as soon as you have adjusted the adjust plate. Under 1 6 Installing and removing the grinding wheel 1. - Page 9 Sharpening planer blade screw Thumb 1. How to fit planer blade holder set In the case of fitting the planer blade to side Blade gauge slider, two thumb screws of planer blade holder should be tightened that the slider should always be contacted Ease gauge closely with the blade gauge A side, and...
- Page 10 Assembling circular saw sharpening kit 1. First install fixed rod with cross point into hole in the inclining tool rest. Secure with thumb screw that screw end fits into indentation on the rod. 2. Now slide rod for mounting saw blade holder and nut into hole below on cross point.
- Page 11 2. Loosen thumb screws and move blade in closer to the grinding wheel. Make sure blade lies flat on top of the inclining tool rest. Secure thumb screws. 3. Using the two adjust screws (6, the right side, work the sliding rod side- ways until the tip of the saw blade just contacts the side of the grinding wheel.
- Page 12 5. Keep clearance of approximately 2mm (3/32") between the wheel and the blade teeth for turning. Secure thumb screw. Next, draw blade up to wheel that the wheel is well into the tooth gullet. Use adjust screws (B, for fixed set- ting that will assure uniform gullet depth when sharpening.
- Page 13 ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only the proper and intended manner.
- Page 14 125 mm (5") BENCH GRINDER Model 9300 Note: The switch and other part configurations may differ from country to cointry.
- Page 15 Rubber Cap Rivet H. Nu1 M12 Name Plate Wave Washer 26 Sllde Plate P. H. Screw M4x8 (Wifh Washed Makita b b e l EYE SHIELD ASSEMBLY tiOUslng H. Screw M4x8 (With Washed Mocor Housing Cover Screw Nut M12 M4x18 (Wnh Warherl...
- Page 16 MAKITA LIMITED O N E YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.