Table of Contents Before You Start Compliance Information ..................Important Safety Instructions ................. Copyright Information ..................... Getting Started Unwrapping The Monitor ..................Package Contents ....................Quick Installation ....................Adjusting The Visual Angle ..................Using the LCD Display Operation Of The Control Panel ................Using The On Screen Display (OSD) Menu ............
Compliance Information FCC Safety Compliance The equipment meets by the test proof the restriction of the relevant B series digital device of Article 15, FCC regulations. The design purpose of these restriction is to provide reasonable protection for daily life at home against the environmental harmful interference. The equipment will generate harmful interference to the radio communications if it is not installed according to the instructions.
Important Safety Instructions Only Use The Specified Power Voltage. Using incorrect voltage will cause a failure, and may possibly result in a fire hazard or a risk of electric shock. Do Not Tamper With Or Damage The Provided Cables Do not pull on, bend or place any object on top of the power or signal cables. Doing so may damage the cable resulting in a poor signal connection, unsteady power, fire hazard or risk of electric shock.
Trademark Acknowledgments: - Honeywell International Inc. makes no representation or warranties with respect to this product. - The Honeywell trademark is used by Soyo Inc. under license from Honeywell International Inc. - Macintosh is a trademark of Apple Computer, Inc.
Getting Started Unwrapping The Monitor: Note: Make sure the power outlet that the monitor will be connected to a standard 110-240 Volt power outlet. Using the incorrect voltage will cause a failure and may possibly result in a risk of fire hazard or electric shock. 1.
Quick Installation Connecting The Monitor To The PC: 1. First, make sure the power is shut off to all units. 2. Connect one end of the video cable (VGA or DVI) to the corresponding port on the back of the LCD monitor and the other end to the corresponding port on the back of your PC. Fasten each end of the video cable with the built-in thumb screws to ensure a good connection.
Adjusting the Visual Angle Adjusting The Monitor: This LCD Monitor can adjust in eight different directions to meet your viewing needs. Note: Do not touch the screen when adjusting the monitor. Doing so could result in damage to the screen Adjustments: Vertical Height - Lift up or down on the display to adjust to your desired height Vertical Tilt - Press forward and pull back on the top and bottom of the display to vertically tilt...
Using the LCD Display Operation Of The Control Panel The control panel is designed to control the On Screen Display (OSD) menu. Three are five function keys located on the side of the monitor used to navigate through the menu. Function Key Description of Function Menu Press to display OSD Menu or enter a sub-menu Press to scroll through the OSD menu and to increase the value of OSD options.
Using the LCD Display (Continued) Adjusting The Screen Automatically At any time, while not in the OSD Menu, pressing the “AUTO” button on the control panel will auto adjust the positioning, brightness, contrast and color of your display. An “Auto Adjustment” message displayed for a few seconds until the adjustment finishes. Note: Auto Adjustment function will be disabled under DVI mode, as in this mode, the screen will be adjusted to the best visual result automatically and there is no need to make further adjustment.
Other Information Specifications Panel Size 19” Resolution 1440 x 900 Contrast Ratio 700:1 Brightness 300 Nits Response Time Viewing Angle 176° Display Colors 16.7 Million Connectors 1 x VGA, 1 x DVI, 4 x USB 2.0 Output, 1 x USB 2.0 Input, 1 Audio Input (3.5mm) Adjustable Height 3.5”...
Troubleshooting If the monitor is not operating properly, try the following steps to help solve the problem: 1. If color or display does not look correct, please refer to the OSD Menu section to adjust your screen settings. 2. Refer to the troubleshooting chart below: Checkpoints Symptoms Make sure the power plug is fully plugged into the wall outlet...
Customer Support For Technical support or product service, please contact us using the information below: United States Web Support: Visit www.honeywellce.com Telephone: 1888-773-HWCE (4923) Fax: 1909-937-0783 Email: support@honeywellce.com General Disclaimer: We have made every effort to ensure that the information and procedures in this guide are as accurate and complete as possible;...
Cleaning the LCD Display Warning: Do not pour or spray any liquid directly onto the monitor. Doing so could result in permanent damage to the device and create a fire hazard or risk of electric shock. 1. For your safety, please turn off the power switch and unplug the monitor before you clean the display. 2.
Honeywell International Inc. makes no representation or warranties with respect to this product. SOYO, Inc. warrants all Honeywell LCD monitor products you have purchased from SOYO or from a SOYO authorized reseller / retailer to be free from defects in materi- als and workmanship under normal use during the warranty period and subject to the terms and conditions set forth below, in the continental United State, Hawaii, Alaska and Canada.