Cisco ISE - Line Card ISE Configuration Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Hardware
  5. ISE - Line Card ISE
  6. Configuration manual
Cisco ISE - Line Card ISE Configuration Manual

Cisco ISE - Line Card ISE Configuration Manual

4-port atm ise line card
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Software Configuration of ATM ISE Line Cards for
Cisco 12000 Series Routers
This feature module describes the software configuration for the Cisco 4-Port ATM Internet Services
Engine (ISE) line cards in the Cisco 12000 Series Router. The line card comes in two variations:
OC-12c/STM-4c and OC-3c/STM-1; otherwise, the features are the same on both cards.
Feature History for the 4-Port ATM ISE Line Card
Release
12.0(25)S
12.0(26)S2
12.0(27)S1
Finding Support Information for Platforms and Cisco IOS Software Images
Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image
support. Access Cisco Feature Navigator at http://www.cisco.com/go/fn. You must have an account on
Cisco.com. If you do not have an account or have forgotten your username or password, click Cancel at
the login dialog box and follow the instructions that appear.
Contents
•
•
•
•
•
•
•
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2004 Cisco Systems, Inc. All rights reserved.
Modification
The 4-Port OC-12c/STM-4c ATM ISE line card was introduced.
The 4-Port OC-3c/STM-1 ATM ISE line card was integrated into 12.0(26)S.
The 4-Port OC-3c/STM-1 ATM ISE line card was introduced. AToM,
Layer 2/Layer 3 features on a single port and enhanced QoS policing
features were introduced.

Advertisement

Table of Contents
loading

Related Manuals for Cisco ISE - Line Card ISE

Summary of Contents for Cisco ISE - Line Card ISE

  • Page 1: Table Of Contents

    Access Cisco Feature Navigator at http://www.cisco.com/go/fn. You must have an account on Cisco.com. If you do not have an account or have forgotten your username or password, click Cancel at the login dialog box and follow the instructions that appear.

  • Page 2: Prerequisites For The 4-Port Atm Ise Line Card

    Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Prerequisites for the 4-Port ATM ISE Line Card Configuring Modular QoS CLI, page 84 • Additional References, page 91 • Command Reference, page 92 • Glossary, page 98 •...

  • Page 3: Information About The 4-Port Atm Ise Line Card

    (LLQ). Both per-VC Weighted Random Early Detection (WRED) and per-VC MDRR are performed in the hardware. The 4-Port OC-12c/STM-4c ATM ISE line card provides the Cisco 12000 Series Router with four 622-Mbps ATM interfaces. The 4-Port OC-3c/STM-1 ATM ISE line card provides four 155-Mbps ATM interfaces.
  • Page 4 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Information About the 4-Port ATM ISE Line Card F4 and F5 flows of operation, administration, and maintenance (OAM) cells and OAM management • specified as requirements by [UNI 3.x] [I.610].

  • Page 5: How To Perform A Basic Configuration Of The 4-Port Atm Ise Line Card

    Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Perform a Basic Configuration of the 4-Port ATM ISE Line Card Any Transport over Multiprotocol Label Switching (MPLS) [AToM]. • ATM OAM Emulation • Cell-based policing •...

  • Page 6: Configuration Basics

    Be prepared with the information that you will need, such as the interface IP address. The Cisco 12000 Series Router identifies an interface address by its line card slot number and port number, in the format slot/port. Because each 4-Port ATM ISE line card contains four ATM interfaces, the port numbers are 0 to 3.

  • Page 7: Troubleshooting Tips

    Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Perform a Basic Configuration of the 4-Port ATM ISE Line Card Command or Action Purpose Step 6 Change the state of the interface to up and enable the no shutdown interface.

  • Page 8: How To Configure Layer 3 Terminated Vcs On The 4-Port Atm Ise Line Card

    All virtual circuit characteristics apply to PVCs. When a PVC is configured, all configuration options are passed to the 4-Port ATM ISE line card. These PVCs are written to the nonvolatile RAM (NVRAM) as part of the configuration and are used when the Cisco IOS image is reloaded.
  • Page 9 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card The syntax of the atm pvp command is: atm pvp vpi vpi is the ATM network VPI to use for this virtual circuit, in the range of 0 to 255 for UNI or 0 to 4095 for NNI;...
  • Page 10 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card For VBR connections in which the sustainable cell rate (SCR) is not equal to the PCR value, the CDVT Note is significantly lower.
  • Page 11 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 4 Specifies a PVC with the specified VPI and virtual circuit pvc [name] vpi/vci identifier (VCI).
  • Page 12 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card DETAILED STEPS Command or Action Purpose Step 1 Enables privileged EXEC mode. enable Enter your password if prompted.
  • Page 13 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 7 Configures ATM OAM F5 continuity check (CC) management to...
  • Page 14 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card The 4-Port ATM ISE line card implements two types of OAM cells: CC cells for fault management and CC cells for activation and deactivation.
  • Page 15 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card exit interface atmslot/port.subifnum pvc vpi/vci service-policy {input | output} policy-name DETAILED STEPS Command or Action...
  • Page 16 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 11 Specifies the ATM subinterface to configure. interface atmslot/port.subifnum Example: Router(config)# interface atm1/0.1...
  • Page 17 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card SUMMARY STEPS enable configure terminal policy-map policy-name class class-default queue-limit cells cells (for egress queue) or queue-limit packets packets (for ingress queue)
  • Page 18 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 8 Specifies the ATM subinterface to configure. interface atmslot/port.subifnum point-to-point Example: Router(config)# interface atm4/0.1...
  • Page 19 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card pvc vpi/vci service-policy output policy-name DETAILED STEPS Command or Action Purpose Step 1 Enables privileged EXEC mode.
  • Page 20 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 9 Specifies the minimum and maximum cell thresholds and,...
  • Page 21 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Set the MTU as low as possible on each subinterface, using the ip mtu command, while still •...
  • Page 22 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 3 Specifies the name of the traffic policy to configure.
  • Page 23 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Examples Following are additional examples of configuring MDRR: Configuring Per-VC MDRR and Low Latency Queueing with Queue Limits •...
  • Page 24 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card In this task, use one of either Step Step Step Step 11, or Step 12, depending on what bits you need to configure.
  • Page 25 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 5 Exits class-map mode. exit Step 6 Specifies the name of the traffic policy to configure.
  • Page 26 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Examples Following are examples of configuring the IP DSCP value and the ATM CLP bit: Configuring the IP DSCP Value, page 26 •...
  • Page 27 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Router(config)# class-map match-any prec01 Router(config-cmap)# match ip prec 0 1 Router(config)# class-map match-any prec345...
  • Page 28 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Configuring and Managing VC Bundles See the following sections for configuration tasks for the VC bundle management feature. Each task in the list is identified as either required or optional.
  • Page 29 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Command Purpose Configures the Inverse ARP time period for all VC bundle Router(config-if-atm-bundle)# inarp minutes members.
  • Page 30 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Committing a VC to a Bundle To add a VC to an existing bundle and enter bundle-vc configuration mode, use the following command...
  • Page 31 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Command Purpose Configures the bundle member to be an individually protected VC Router(config-if-atm-member)# protect {group | bundle member.

  • Page 32: Vc Bundle Examples

    Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Command Purpose Configures VBR-RT as the traffic shaping rule for the VC, Router(config-vc-class)# vbr-rt pcr scr [mbs] qualified by peak cell rate (pcr), sustainable cell rate (scr), and optional maximum burst cell size (mbs).
  • Page 33 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card pvc-bundle 1/105 precedence 5 pvc-bundle 1/104 precedence 4 pvc-bundle 1/103 precedence 3 pvc-bundle 1/102...
  • Page 34 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card CLP Bit Setting on a Per-Experimental Basis with VC Bundling CLP bit setting can be combined with VC bundling by configuring VC bundling on a group of VCs as desired, creating a policy map with CLP bit setting configured as desired, and then configuring the CLP bit setting.

  • Page 35: How To Configure Atom Vcs On The 4-Port Atm Ise Line Card

    The purpose of bridged permanent virtual circuits (BPVCs) is to allow ATM interfaces in the Cisco high-end router to be used in an edge or aggregation role and connect to a Cisco Catalyst switch or to another remote device that supports bridged-format RFC 1483 PDUs only.
  • Page 36 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card A permanent virtual path (PVP) is like a bundle of VCs, transporting all cells with a common VPI, rather than a specific VPI and VCI.
  • Page 37 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Configuring ATM Cell Packing over MPLS on PVCs, page 42 – Configuring ATM Cell Packing over MPLS on PVPs, page 44 –...
  • Page 38 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card DETAILED STEPS Command Purpose Step 1 Enables privileged EXEC mode. enable Enter your password if prompted.
  • Page 39 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card SUMMARY STEPS enable configure terminal interface atmslot/port pvc vpi/vci l2transport encapsulation aal0 xconnect peer-router-id vcid encapsulation mpls...
  • Page 40 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Router(config-atm-l2trans-pvc)# xconnect 13.13.13.13 100 encapsulation mpls Configuring ATM Cell Relay over MPLS on PVPs Perform this task to configure ATM Cell Relay on permanent virtual paths (PVPs).
  • Page 41 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Example Router> enable Router# configure terminal Router(config)# interface atm1/0 Router(config-if)# atm pvp vpi 1 l2transport Router(config-atm-l2trans-pvc)# xconnect 13.13.13.13 100 encapsulation mpls...
  • Page 42 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 3 Specifies an ATM interface. interface atmslot/port Example: Router(config)# interface atm1/0 Step 4 Binds the attachment circuit to the interface.
  • Page 43 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card DETAILED STEPS Command Purpose Step 1 Enables privileged EXEC mode. enable Enter your password if prompted.
  • Page 44 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Router# configure terminal Router(config)# interface atm1/0 Router(config-if)# atm mcpt-timers 100 200 1000 Router(config-if)# pvc 0/100 l2transport...
  • Page 45 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command Purpose Step 4 Sets up the cell-packing timers, which specify how long the PE atm mcpt-timers [timer1-timeout timer2-timeout timer3-timeout] router can wait for cells to be packed into an MPLS packet.
  • Page 46 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card The number of cells that can be packed varies from 2 to 28. • SUMMARY STEPS...
  • Page 47 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 7 Sets up the cell-packing timers, which specify how long the...
  • Page 48 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card SUMMARY STEPS enable configure terminal interface atmslot/port pvc vpi/vci l2transport encapsulation aal5 oam emulation-enable oam-pvc manage [frequency]...
  • Page 49 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card OAM Emulation should be configured at both ends of the VC. Note Example Router> enable Router# configure terminal...
  • Page 50 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Restrictions When traffic shaping is configured on a VC, the cell delay variation (CDV) is set for the VC. This value will change according to the shaping class defined.
  • Page 51 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card DETAILED STEPS Command or Action Purpose Step 1 Enables privileged EXEC mode. enable Enter your password if prompted.
  • Page 52 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 11 For ATM Cell Relay, this command specifies raw cell encapsulation aal0 encapsulation for the interface.
  • Page 53 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card policy-map policy-map-name class class-default queue-limit number-of-cells cells exit exit interface atmslot/port atm clock internal atm pvp vpi l2transport...
  • Page 54 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 8 Specifies an ATM interface or subinterface to configure. interface atmslot/port...
  • Page 55 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Configuring Cell Packing over MPLS on PVCs This task illustrates the configuration of VBR-RT traffic shaping in cell packing over MPLS VC mode.
  • Page 56 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 5 Specifies or modifies the maximum number of cells the queue-limit number-of-cells cells queue can hold for a class policy configured in a policy map.
  • Page 57 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 14 Specifies VBR-rt shaping. vbr-rt pcr scr burst The pcr value indicates the peak cell rate, and its range is from 38 to 622000 Kbps.
  • Page 58 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card class class-default queue-limit number-of-cells cells exit exit interface atmslot/port atm clock internal atm pvp vpi l2transport...
  • Page 59 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 8 Specifies an ATM interface or subinterface to configure. interface atmslot/port...
  • Page 60 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Router(config-pmap)# exit Router(config)# interface atm1/0 Router(config)# atm clock internal Router(config-if)# atm pvp 100 l2transport Router(config-atm-l2trans-pvc)# cell-packing 10 mcpt-timer 1...
  • Page 61 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 3 Specifies the name of the service policy to configure with policy-map policy-map-name the shaping queue size.
  • Page 62 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 12 Specifies VBR-rt shaping. vbr-rt pcr scr burst The pcr value indicates the peak cell rate, and its range is from 38 to 622000 Kbps.
  • Page 63 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card See the “Troubleshooting ATM Errors on the 4-Port ATM ISE Line Card” section on page 76 for more information on the output from these commands.
  • Page 64 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Policing is supported on the 508 channels that can be used for cell packing or cell relay. The rest of •...
  • Page 65 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 3 Specifies the name of the service policy to configure. policy-map policy-map-name...
  • Page 66 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card DETAILED STEPS Command or Action Purpose Step 1 Enables privileged EXEC mode. enable Enter your password if prompted.
  • Page 67 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 10 (Optional) Specifies the value used to set the MPLS EXP set mpls experimental mpls-exp-value bits defined by the policy map.
  • Page 68 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card DETAILED STEPS Command or Action Purpose Step 1 Enables privileged EXEC mode. enable Enter your password if prompted.
  • Page 69 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 10 Exits policy map mode. exit Example: Router(config-pmap)# exit Step 11 Specifies the name of the parent service policy to configure.
  • Page 70 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card class clp0 police rate scr cps atm-mbs mbs cells conform-action transmit exceed-action transmit exit exit policy-map vbr3...
  • Page 71 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 8 Specifies a maximum bandwidth usage by a traffic class police rate scr cps atm-mbs mbs cells conform-action transmit exceed-action drop through the use of a token bucket algorithm.
  • Page 72 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Attaching a Service Policy to a PVC After you define a service policy with the desired QoS configuration, you must attach it to a PVC as described in this task.
  • Page 73 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 7 Binds the attachment circuit to a pseudowire VC or VP.
  • Page 74 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card exit exit interface atmslot/port pvc vpi l2transport service-policy input policy-map-name xconnect peer-router-id vcid encapsulation mpls DETAILED STEPS...
  • Page 75 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure AToM VCs on the 4-Port ATM ISE Line Card Command or Action Purpose Step 9 Assigns a virtual path identifier (VPI) and virtual circuit pvc vpi/vci l2transport identifier (VCI).

  • Page 76: Troubleshooting Atm Errors On The 4-Port Atm Ise Line Card

    Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Troubleshooting ATM Errors on the 4-Port ATM ISE Line Card Command or Action Purpose Step 3 Specifies the name of the child service policy to configure. policy-map policy-map-name...

  • Page 77: Troubleshooting Commands

    Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Troubleshooting ATM Errors on the 4-Port ATM ISE Line Card Upgrading the FPGA Image, page 83 • Troubleshooting Commands Use the following commands to troubleshoot ATM errors: show interfaces atm •...
  • Page 78 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Troubleshooting ATM Errors on the 4-Port ATM ISE Line Card Table 8 show interfaces Error Counter Descriptions (continued) Error Counter Description Abort The number of packet reassemblies that failed because of receiving a trailer length of 0.
  • Page 79 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Troubleshooting ATM Errors on the 4-Port ATM ISE Line Card Table 9 show controller atm Counters Counter Description Comments tx_packets A 64-bit counter of the number of packets...
  • Page 80 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Troubleshooting ATM Errors on the 4-Port ATM ISE Line Card Table 9 show controller atm Counters (continued) Counter Description Comments rx_total_resource_errs The total number of packet reassemblies that This error is not likely failed due to resource exhaustion.
  • Page 81 To display per-VC counters, first you must determine what connection ID is associated with the VC. This procedure differs slightly, depending on the version of Cisco IOS you are running. The following procedure describes how to display the per-VC counters in Cisco IOS release 12.0(27)S or later.
  • Page 82 Current average queue depth (in number of cells) as calculated by the WRED algorithm. The following procedure describes how to display the per-VC counters in Cisco IOS releases 12.0(26)S and 12.0(25)S. Step 1 Retrieve the VCD by using the show atm pvc command on the RP.
  • Page 83 12000 Series Internet Router publication. When the Cisco IOS image boots, it verifies that a compatible FPGA image is running on the router. The major version number of the FPGA image must be the same as that expected by the Cisco IOS image;...

  • Page 84: Configuring Modular Qos Cli

    Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Configuring Modular QoS CLI Configuring Modular QoS CLI The Modular QoS CLI (MQC) is a CLI structure that allows users to create traffic policies and attach these policies to interfaces. A traffic policy contains a traffic class and one or more QoS features. A traffic class is used to classify traffic, while the QoS features in the traffic policy determine how to treat the classified traffic.
  • Page 85 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Configuring Modular QoS CLI Command Purpose Specifies the MPLS values to use as match criteria against which Router(config-cmap)# match mpls experimental mpls-values packets are checked to determine if they belong to the class.
  • Page 86 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Configuring Modular QoS CLI The syntax of the policy-map command is: policy-map policy-name no policy-map policy-name The syntax of the class command is: class class-name no class class-name In addition to any user-defined classes, a pre-existing class named class-default exists.
  • Page 87 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Configuring Modular QoS CLI Command or Action Purpose Specifies a bandwidth usage and conformance policy by a traffic police bps burst-normal burst-max conform-action action exceed-action action class through the use of a token bucket algorithm. For a description...
  • Page 88 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Configuring Modular QoS CLI Command or Action Purpose Specifies the IP DSCP of packets within a traffic class. The IP DSCP set ip dscp ip-dscp-value value can be any value between 0 and 63.
  • Page 89 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Configuring Modular QoS CLI Command or Action Purpose Specifies the name of a predefined class, which was defined with the class class-name class-map command, to be included in the traffic policy. You can include the default class, class-default, in the traffic policy.
  • Page 90 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Configuring Modular QoS CLI Command or Action Purpose Specifies the minimum and maximum cell thresholds and, random-detect precedence precedence min-threshold packets max-threshold packets optionally, the mark-probability denominator for the precedence [mark-prob-denominator value.

  • Page 91: Additional References

    ATM Forum Traffic Management Specification 4.0 MIBs In addition to industry-standard Simple Network Management Protocol (SNMP) and other Management Information Bases (MIBs) supported on the Cisco 12000 Series Router, the 4-Port ATM ISE line card supports the following: • ATM-MIB •...

  • Page 92: Technical Assistance

    Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Command Reference CISCO-CLASS-BASED-QOS-MIB • CISCO-CLASS-BASED-QOS-CAPABILITY-MIB • To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL: http://www.cisco.com/go/mibs RFCs RFCs Title...
  • Page 93 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers police rate police rate To configure traffic policing, use the police rate command in policy-map class configuration mode. To remove traffic policing from the configuration, use the no form of this command.
  • Page 94 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers police rate violate-action (Optional) Action to take on packets that violate the normal and maximum burst sizes. action Action to take on packets. Specify one of the following keywords: drop—Drops the packet.
  • Page 95 The police rate command can be used with the Traffic Policing feature. The Traffic Policing feature works with a token bucket algorithm. Two types of token bucket algorithms are in Cisco IOS Release 12.1(5)T: a one-token bucket algorithm and a two-token bucket algorithm. A one-token bucket system is used when the violate-action option is not specified, and a two-token bucket system is used when the violate-action option is specified.
  • Page 96 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers police rate Tokens are updated in the conform bucket. If the previous arrival of the packet was at T1 and the • current arrival of the packet is at T, the bucket is updated with T -T1 worth of bits based on the token arrival rate.
  • Page 97 Weighted Random Early Detection (WRED) randomly drops some packets with the specified DSCP value. cells On the 4-Port ATM ISE line card for the Cisco 12000 Series Router, the min-threshold and max-threshold values must be specified as a count of ATM cells. max-threshold Maximum threshold in number of cells.

  • Page 98: Glossary

    Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Glossary Usage Guidelines The random-detect dscp command allows you to specify the DSCP value. The DSCP value can be a number from 0 to 63, or it can be one of the following keywords: ef, af11, af12, af13, af21, af22, af23, af31, af32, af33, af41, af42, af43, cs1, cs2, cs3, cs4, cs5, or cs7.
  • Page 99 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Glossary Term Description label switched path maximum burst cell size MCPT maximum cell packing timeout MDRR Modified Deficit Round Robin Management Information Base MPLS Multiprotocol Label Switching Modular Quality of Service CLI...

  • Page 100: Vpn Virtual Private Network

    Note CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco...
  • Page 101 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Glossary Cisco IOS Release 12.0(27)S...
  • Page 102 Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers Glossary Cisco IOS Release 12.0(27)S...

Table of Contents