Page 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.
Maximum Capacity (Table Only) .....350 lbs. Operating Length......57-1/2 - 124 in. Operating Height ..... 33-3/4 - 37-3/4 in. Net Weight ..........61 lbs. Manufacture Date Shipping Weight ........71 lbs. Collapsed Dimensions..56-1/2 x 23 x 10-1/8 in. Serial Number Model T33296 (Mfd. Since 07/23)
Never operate under the influence of drugs or injury or blindness from flying particles. Everyday alcohol, when tired, or when distracted. eyeglasses are NOT approved safety glasses. Model T33296 (Mfd. Since 07/23)
Page 6
EXPERIENCING DIFFICULTIES. If at any time debris. Make sure they are properly installed, you experience difficulties performing the intend- undamaged, and working correctly BEFORE ed operation, stop using the machine! Contact our operating machine. Technical Support at (570) 546-9663. Model T33296 (Mfd. Since 07/23)
IMPORTANT: Save all packaging materials until — Hex Nuts M6-1 ........4 you are completely satisfied with the machine and T-Supports..........2 have resolved any issues between Grizzly or the — Knobs ............ 2 shipping agent. You MUST have the original pack- — Carriage Bolts M6-1 x 55.......
Below is the minimum amount of space needed for the machine. 124" " " Figure 3. Minimum working clearances. Figure 2. T33296 inventory small parts. Model T33296 (Mfd. Since 07/23)
Foot Pedal At this point miter stand will be locked in its fully unfolded position, as shown in Figure 8. Stow Lock Lock Ring Figure 5. Releasing stow lock. Figure 8. Miter stand locked upside down. Model T33296 (Mfd. Since 07/23)
Page 11
(4) M6-1 lock nuts. Outside Skid Frame 17. Position both handle bars pointing down- ward, as shown in Figure 14, and fasten using screws making sure smooth heads are Figure 10. Skid frame installed. facing outward. Model T33296 (Mfd. Since 07/23)
Installing Miter Saw If installing or removing saw from table alone, you may have to overreach, adding The Model T33296 miter saw stand features two extra stress to lower back. To avoid lower adjustable clamping rails that have a series of ⁄...
Page 14
(4) carriage bolts, applicable nuts, and washers shown in Figure 18. Nuts and Washers, as Applicable Clamping Rail Handles on Same Side as Back-Side of Saw Carriage Bolt Offset Mounting Bracket Figure 18. Mounting miter saw. -12- Model T33296 (Mfd. Since 07/23)
12. Uses handle bars and foot bar to stabilize ects. Regardless of the content in this sec- and support weight of stand and saw. tion, Grizzly Industrial will not be held liable for accidents caused by lack of training. 13. Presses foot pedal to release elevation lock, and lifts stand until stow lock engages and locks stand in folded vertical position.
Keep foot firmly on foot bar and lower handle Stop Bolt bars until stand is heard locking in unfolded position. Move and lock saw in operation location, as shown in Figure 19. Figure 20. Saw stow location. -14- Model T33296 (Mfd. Since 07/23)
To reduce this risk, only install accessories amount of ducting. Specifications: 537 CFM, 7.2" recommended for this machine by Grizzly. static pressure, 1.5 cubic foot bag, and 30-micron filter. Motor is 1 HP, 120V/240V, 7A/3.5A.
If rail locking is inadequate, or will not lock, see Clamping Adjustment on Cleaning the Model T33296 is easy. Vacuum Page 17. excess sawdust and wipe off remaining dust with a dry cloth.
Figure 25. Engaged trigger lock. clamping of rail. When satisfied with clamping adjustment, hold screw in position and tighten lock nut. Lock Nut Repeat procedure on remaining clamping rail. Lock Shoe Adjustment Screw Figure 24. Clamping rail adjustment. -17- Model T33296 (Mfd. Since 07/23)
SECTION 6: PARTS We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability. Main -18- BUY PARTS ONLINE AT GRIZZLY.COM! Model T33296 (Mfd.
Page 21
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. -19- BUY PARTS ONLINE AT GRIZZLY.COM!
ROLL PIN 4 X 28 PT33296121 OFFSET MOUNTING BRACKET PT33296110 HOOK PT33296122 FLAT WASHER 8MM PT33296111 ROLL PIN 5 X 28 -20- BUY PARTS ONLINE AT GRIZZLY.COM! Model T33296 (Mfd. Since 07/23) Scan QR code to visit our Parts Store.
WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.