Listening To Music Via Bluetooth Streaming - Makita DMR203 Instruction Manual

NOTE:
Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the
actual capacity.
Using supplied AC power adaptor
Remove the rubber protector and insert the adaptor
plug into the DC socket on the right hand side of the
speaker. Plug the adaptor into a standard mains socket
outlet. Whenever the adaptor is used, the battery pack
is automatically disconnected.
CAUTION:
● Always disconnect the AC power adaptor
completely before moving the speaker. If the AC
adaptor is not removed, it may cause an electric
shock.
● Never pull and/or drag the cord of the adaptor.
If not, the speaker may accidentally fall down,
causing injury to you or someone around you.
IMPORTANT:
● The mains adaptor is used as the means of
connecting the speaker to the mains supply. The
mains socket used for the speaker must remain
accessible during normal use.
● In order to disconnect the speaker, the mains adaptor
should be removed from the mains outlet completely.
● Use the AC power adaptor supplied with the product
or specified by Makita only.
● Do not hold the power supply cable and plug by your
mouth. Doing so might cause an electric shock.
● Do not touch the power plug with wet or greasy
hands.
● Damaged or entangled cords increase the risk
of electric shock. If the cord is damaged, have it
replaced by our authorized service center in order to
avoid a safety hazard. Do not use it before repair.
● After use, always store AC power adaptor out of the
reach of children. If Children play with the cord, they
may suffer injury.
USB power supply socket
This jack can be used to charge a mobile phone or any
other device that uses less than 2.1A of DC current.
Charging will only occur when the speaker is switched on.
NOTE:
Ensure the specification of your external device such as
mobile phone or player is compatible with the speaker.
75% ~ 100%
Please read instruction manual of your external device
before charging.
50% ~ 75%
IMPORTANT:
● Before connecting USB device to the charger, always
25% ~ 50%
● The charger may not supply power to some USB
0% ~ 25%
● When not using or after charging, remove the USB
● Do not connect power source to USB port. Otherwise
● Do not insert a nail, wire, etc. into USB power supply
● Do not connect this USB socket with your PC
You need to pair your Bluetooth device with the speaker
before you can auto-link to play/stream Bluetooth music
through the speaker. Pairing creates a 'bond' so two
devices can recognize each other.
Note:
To have the better sound quality, we recommend
setting the volume to more than two-thirds level on your
Bluetooth device and then adjust the volume on the
speaker as required.
1. Press the Power button to turn on the speaker.
2. Activate Bluetooth on your device according to the
3. Once connected, there will be a confirmation tone
4. Use the controls on your Bluetooth-enabled device or
8 ENGLISH
backup your data of USB device. Otherwise your data
may lose by any possibility.
devices.
cable and close the cover.
there is risk of fire. The USB port is only intended
for charging lower voltage device. Always place the
cover onto the USB port when not charging the lower
voltage device.
port. Otherwise a circuit short may cause smoke and
fire.
USB port, as it is highly possible that it may cause
breakdown of the units.
LISTENING TO MUSIC VIA
BLUETOOTH STREAMING
Pairing your Bluetooth device for the
first time
"Pairing" will appear on the display to show the
speaker is discoverable.
device's user manual to link to the speaker. Locate
the Bluetooth device list and select the device named
"DMR203" (With some mobiles which are equipped
with earlier versions than BT2.1 Bluetooth device,
you may need to input the pass code "0000").
sound. "Paired" will appear on the display. You can
simply select and play any music from your source
device. Volume control can be adjusted from your
source device, or directly from the speaker.
on the speaker to play/pause and navigate tracks.