Cisco Catalyst 9500 Manual page 188

Examples: Displaying SDM Templates
Output Netflow flows:
SGT/DGT (or) MPLS VPN entries:
SGT/DGT (or) MPLS VPN Overflow entries:
Wired clients:
MACSec SPD Entries:
MPLS L3 VPN VRF:
MPLS Labels:
MPLS L3 VPN Routes VRF Mode:
MPLS L3 VPN Routes Prefix Mode:
MVPN MDT Tunnels:
L2 VPN EOMPLS Attachment Circuit:
MAX VPLS Bridge Domains :
MAX VPLS Peers Per Bridge Domain:
MAX VPLS/VPWS Pseudowires :
Ipv4/Ipv6 Direct and Indirect unicast routes share same space
* values can be modified by sdm cl
These values can vary depending on device and version.
The following example output shows the NAT template information on Cisco Catalyst 9500 Series Switches:
Device# show sdm prefer nat
This is the NAT template.
Security Ingress IPv4 Access Control Entries*:
Security Ingress Non-IPv4 Access Control Entries*:
Security Egress IPv4 Access Control Entries*:
Security Egress Non-IPv4 Access Control Entries*:
QoS Ingress IPv4 Access Control Entries*:
QoS Ingress Non-IPv4 Access Control Entries*:
QoS Egress IPv4 Access Control Entries*:
QoS Egress Non-IPv4 Access Control Entries*:
Netflow Input Access Control Entries*:
Netflow Output Access Control Entries*:
Flow SPAN Input Access Control Entries*:
Flow SPAN Output Access Control Entries*:
Number of VLANs:
Unicast MAC addresses:
Overflow Unicast MAC addresses:
Overflow L2 Multicast entries:
L3 Multicast entries:
Overflow L3 Multicast entries:
Ipv4/Ipv6 shared unicast routes:
Overflow shared unicast routes:
Policy Based Routing ACEs / NAT ACEs:
Tunnels:
LISP Instance Mapping Entries:
Control Plane Entries:
Input Netflow flows:
Output Netflow flows:
SGT/DGT (or) MPLS VPN entries:
SGT/DGT (or) MPLS VPN Overflow entries:
Wired clients:
MACSec SPD Entries:
MPLS L3 VPN VRF:
MPLS Labels:
MPLS L3 VPN Routes VRF Mode:
MPLS L3 VPN Routes Prefix Mode:
MVPN MDT Tunnels:
L2 VPN EOMPLS Attachment Circuit:
MAX VPLS Bridge Domains :
MAX VPLS Peers Per Bridge Domain:
MAX VPLS/VPWS Pseudowires :
Ipv4/Ipv6 Direct and Indirect unicast routes share same space
* values can be modified by sdm cli
The following example output shows the SDA template information on Cisco Catalyst 9500 Series Switches:
System Management Configuration Guide, Cisco IOS XE Amsterdam 17.2.x (Catalyst 9500 Switches)
172
Configuring SDM Templates
32768
32768
768
2048
256
1024
45056
209920
32768
1024
1024
1000
128
16384
7168 (current) - 7168
5120 (current) - 5120
3072 (current) - 3072
5120 (current) - 5120
2560 (current) - 2560
1536 (current) - 1536
3072 (current) - 3072
1024 (current) - 1024
1024 (current) - 1024
1024 (current) - 1024
512 (current) - 512
512 (current) - 512
4094
32768
768
2304
32768
768
212992
1536
15872
1792
1024
1024
32768
32768
32768
768
2048
256
1024
45056
209920
32768
1024
1024
1000
128
16384
(proposed)
(proposed)
(proposed)
(proposed)
(proposed)
(proposed)
(proposed)
(proposed)
(proposed)
(proposed)
(proposed)
(proposed)