Makita RP2302FC Instruction Manual
Hide thumbs
Also See for RP2302FC:
- Instruction manual (99 pages) ,
- Instruction manual (96 pages) ,
- Instruction manual (97 pages)
Related Manuals for Makita RP2302FC
Summary of Contents for Makita RP2302FC
- Page 1 INSTRUCTION MANUAL Router RP1802 RP1802F RP1803 RP1803F RP2302FC RP2303FC DOUBLE INSULATION Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: RP1802 RP1802F RP1803 RP1803F RP2302FC RP2303FC Collet chuck capacity 12 mm or 1/2″ Plunge capacity 0 - 70 mm No load speed 23,000 min 22,000 min 9,000 - 23,000 min Overall height 312 mm 327 mm Net weight 6.2 kg... -
Page 3: Ec Declaration Of Conformity
) : 5.1 m/s operating a power tool. Distractions can cause Uncertainty (K) : 1.5 m/s you to lose control. Model RP2302FC Electrical safety Work mode: cutting grooves in MDF Power tool plugs must match the outlet. Never Vibration emission (a ) : 4.2 m/s... - Page 4 Use of power supply via an RCD with a rated residual current of 30 mA or less is always recommended. Power tools can produce electromagnetic fields (EMF) that are not harmful to the user. However, users of pacemakers and other similar medical devices should contact the maker of their device and/or doctor for advice before operating this power tool.
-
Page 5: Router Safety Warnings
Service 21. Keep cord away from your foot or any objects. Otherwise an entangled cord may cause a falling Have your power tool serviced by a qualified accident and result in personal injury. repair person using only identical replacement parts. This will ensure that the safety of the power SAVE THESE INSTRUCTIONS. -
Page 6: Nylon Nut
Nylon nut Switch action CAUTION: CAUTION: Do not lower the nylon nut too low. Before plugging in the tool, always The router bit will protrude dangerously. check to see that the switch trigger actuates properly and returns to the "OFF" position when released. The upper limit of the tool body can be adjusted by CAUTION: Make sure that the shaft lock is... - Page 7 23,000 the tool start smoothly. Lighting up the lamps Constant speed control Only for model RP1802F, RP1803F, RP2302FC, Only for model RP2302FC, RP2303FC RP2303FC Possible to get fine finish, because the rotating speed is kept constant even under the loaded condition.
-
Page 8: Operation
Insert the router bit all the way into the collet cone. Lower the tool body and move the tool forward over the workpiece surface, keeping the base flush and Press the shaft lock to keep the shaft stationary and use advancing smoothly until the cutting is complete. - Page 9 If the distance between the side of the workpiece and Straight guide the cutting position is too wide for the straight guide, or if the side of the workpiece is not straight, the straight The straight guide is effectively used for straight cuts guide cannot be used.
- Page 10 When set to maximum opening width Fine adjusting function for positioning blade in relation to straight guide Fig.20 Templet guide Fig.17 ► 1. Thumb screw (A) 2. Thumb screw (B) 3. Scale ring Optional accessory The templet guide provides a sleeve through which the Loosen the thumb screw (A).
- Page 11 Secure the templet to the workpiece. Place the Install the trimmer guide on the guide holder using the clamp- tool on the templet and move the tool with the templet ing screw (D). Insert the guide holder into the holes in the tool guide sliding along the side of the templet.
-
Page 12: Maintenance
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Fig.30 ► 1. Screw M6 x 135 in a screw hole... -
Page 13: Replacing Carbon Brushes
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. - Page 14 “V”Grooving bit Router bits Straight bit Fig.37 Unit:mm Fig.35 θ Unit:mm 1/4″ 90° Drill point flush trimming bit 1/4″ 1/2″ 1/2″ 1/4″ 1/4″ Fig.38 “U”Grooving bit Unit:mm Fig.36 Unit:mm 14 ENGLISH...
- Page 15 Drill point double flush trimming bit Corner rounding bit Fig.39 Fig.41 Unit:mm Unit:mm Board-jointing bit Chamfering bit Fig.40 Fig.42 Unit:mm Unit:mm θ 30° 45° 60° 15 ENGLISH...
- Page 16 Cove beading bit Ball bearing corner rounding bit Fig.43 Fig.45 Unit:mm Unit:mm 1/4″ Ball bearing flush trimming bit Ball bearing chamfering bit Fig.44 Fig.46 Unit:mm Unit:mm θ 1/4″ 45° 1/4″ 60° 16 ENGLISH...
- Page 17 Ball bearing beading bit Ball bearing roman ogee bit Fig.47 Fig.49 Unit:mm Unit:mm Ball bearing cove beading bit Fig.48 Unit:mm ENGLISH...
- Page 20 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885917B222 www.makita.com 20211030...