Related Manuals for Honeywell H18TFW
Summary of Contents for Honeywell H18TFW
- Page 1 18 Cubic Feet Refrigerator With Freezer User Manual Read and save these instructions before use H18TFW H18TFS...
-
Page 2: Table Of Contents
CONTENTS 1 Safety Warnings ............... . . 1 1.1 Warning 2 Proper Use of Refrigerator 2.1 Installation... -
Page 3: Safety Warnings
1 SAFETY WARNINGS 1.1 Warning 1.1 Warning WARNING: risk of fire / flammable materials This appliance is intended to be used in household, non-retail applications. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. -
Page 4: Proper Use Of Refrigerator
2 PROPER USE OF REFRIGERATOR 2.1 Installation When selecting a position for your unit you should make sure the floor is flat and firm, and the room is well ventilated. Avoid placing your unit near a heat source. Avoid direct sunlight as it may increase the electrical consumption. Extremely cold temperatures may also cause the unit not to perform properly. - Page 5 02 Removing the freezer door Remove the hinge cover and cover plate. Then remove the upper hinge with a cross head screwdriver. Raise the freezer door upward. Cover plate Hinge Cover Top Hinge 03 Removing the refrigerator door Remove the middle hinge with a cross screwdriver. Raise the cold storage door upward.
- Page 6 05 Replacing the door accessories Take out the top hinge and hinge shaft hole plate from the top of freezer and refrigerator doors. Fit the top hinge on the other side of door. Remove the bottom hinge, and fix it to the other side of the door with screws. Take the middle hinge, and fix them to the left side of freezer door.
- Page 7 08 Removing the handles Remove the handle caps. Screw the handle fastening screws with an Allen key. Remove the handle. 09 Fitting the handles Remove the screws from the handles and fit them on the other side of the door. Place the handle into the handle bolts and screw it tightly with the Allen key.
-
Page 8: Leveling The Unit
11 Flipping the handle of the appliance doors When the door is changed between left and right, the refrigerator handle (A) is placed on the freezer, and the freezer handle (B) is placed on the refrigerator. 2.4 Leveling the Unit To raise the appliance, turn the feet clockwise. -
Page 9: Before Using Your Unit
2.5 Before Using Your Unit Before plugging in You must check that you have a socket which is compatible with the plug supplied within the unit. Before turning on Do not turn on until two hours after moving the unit. 2.6 Interior Accessories Various glass or plastic storage shelves are included with your appliance - different models have different combinations. -
Page 10: Ice Maker Installation
2.7 Ice Maker Installation Remove a protective cover before connecting the wire of the ice machine in the box. Tools Required: • 1/4 inch copper supply line with shut off valve • 1/4 inch brass compression nut and ferrule The copper tubing and shut off valve are available in a kit from your local hardware or plumbing supply store. - Page 11 Tools Required: • Putty Knife • Pliers • 1/4 inch Socket Wrench • Needle Nose Pliers or Nut Driver • Adjustable Wrench • Knife 01 Unplug the refrigerator from the wall outlet. 02 Remove the ice tray from the freezer. 03 Move the shelf to the next partition.
- Page 12 07 Push water inlet tube into small hole on the back of the refrigerator. Rotate while inserting tube until flat surface of inlet tube is tight against the back of the refrigerator. 08 Push plastic water supply tubing into water inlet tube as far as it will go and manually tighten nylon compression nut onto threaded end of inlet tube.
- Page 13 12 Mount the ice maker onto the two screws you installed in step 10. Tighten screws. Make sure water inlet tube is sitting inside the fill cup. 13 Adjust the leveling bracket to level ice maker. Ice maker is level when gap between freezer wall and ice maker is the same at the top and bottom.
-
Page 14: Connecting Ice Maker To Water Supply
16 Connect wiring harness to water valve. Make sure connection is tight. Wiring Harness 17 Push plastic water supply tubing into the bottom of the water valve as far as it will go. Manually tighten the nylon nut onto the threaded end of the water valve. - Page 15 Before installing the water supply line, you will need: • Basic tools: adjustable wrench, flat head screwdriver, and phillips screwdriver. • Access to a household cold water line with water pressure between 20 and 120 psi. • A water supply line made of 1/4 inch (6.4 mm) OD, copper tubing. To determine the length of copper tubing needed, you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe.
- Page 16 2.8 Connecting Ice Maker to Water Supply Plastic Water Steel Clamp Tubing Brass Compression Nut Ferrule (metal ring) Water Valve Bracket Water Inlet Water Valve Include enough tubing in loop to move refrigerator out for cleaning Copper Water Line (From Household Water Supply) To connect water supply line to ice maker inlet valve: 01 Disconnect refrigerator from electric power supply.
-
Page 17: Product Overview
3 PRODUCT OVERVIEW 3.1 Key Components... -
Page 18: Operation
4 OPERATION 4.1 Display 1 2 3 4 5 01 Buttons Button (A): Press this button to shift between temperatures Buttons (1-5): 1 is the warmest setting, 5 is the coldest setting Button (B): When the fridge is running, press the standby button (B) for 3 seconds to put the refrigerator into standby mode. -
Page 19: Temperature Control Operation
4.3 Temperature Control Operation 01 The freezer is automatically in the mid temperature setting. 02 If the freezer is in the COLDER position when the temperature is lower than 10ºF. The fridge temperature will be automatically changed to the 4 or 5 temperature setting. 03 If the freezer is in the COLD position when the temperature is lower than 40ºF. -
Page 20: Cleaning
5 CLEANING 5.1 Defrosting Auto-defrost for frost-free refrigerator. 5.2 Cleaning the Interior and the Exterior of the Unit • Remove all the shelves and the salad bin. To remove the salad bin, first remove the lower door shelf. • Wipe the inside of the unit with a weak solution of bicarbonate soda and then rinse with warm water using a wrung-out sponge or cloth. -
Page 21: Maintenance
6 MAINTENANCE 6.1 Changing the Internal Light Setting the refrigerator control to off does not remove power to the light circuit. CAUTION: Light bulb may be hot. Illuminating lamp parameter: MAX 40W 01 Unplug the refrigerator. 02 The bulb is located at the top of the compartment near the opening. 03 Replace with an appliance bulb of the same or lower wattage. -
Page 22: Troubleshooting
7 TROUBLESHOOTING 7 TROUBLESHOOTING Ensure the appliance is plugged in and connected to power Inoperation Check that the voltage is not low The temperature control knob is not set to “OFF“ Odor Thoroughly clean the interior of the refrigerator. Do not overload the appliance Long-term operation Do not put hot contents in the appliance of compressor... - Page 24 If your product needs repair, please contact us via email or phone. ©2021 BHRS Group, LLC. All Rights Reserved. BHRS Group, LLC The Honeywell Trademark is used under license from 585 Prospect St. Honeywell International Inc. Honeywell International Lakewood, NJ 08701 Inc.