Makita DTR180 Instruction Manual page 5

16. When you have completed the wire tying pro-
cess, pull the tool up vertically. Otherwise, the
arm may be caught on rebars, which may cause
an accident.
17. Be careful not to drop, bump, or hit the tool.
If a strong impact is applied prior to the tool
being used, make sure that the tool is not dam-
aged or cracked, and that the safety devices
operate normally. Otherwise, an accident may
occur.
18. If any of the following phenomena occur, lock
the trigger, turn the power switch off, and
remove the battery cartridge from the tool.
If the tool operates incorrectly, an accident may
occur.
• If an operating sound is heard as soon as
the battery cartridge is mounted.
• If overheating or abnormal smells or
noises are detected.
When you are taking measures in
•
response to the error display. (Ask your
local Makita Service Center for repairs.)
When loading or unloading a wire reel.
•
• When you move while holding the tool
during work.
• When you do not use the tool.
When you inspect or adjust the tool.
•
• When you remove a stranded wire.
19. When working on scaffolding, always stabilize
it and work using a posture that will ensure
you maintain your balance. If scaffolding is
unstable, an accident may occur.
20. When working on a roof or similar locations,
move in a forward direction while working so
that you can see where you are going. If you
move in a backward direction while working, you
may lose your footing and cause an accident.
21. If you are working in a highly elevated loca-
tion, ensure that no one is below you, and pay
attention to ensure you do not drop any tools
while working. Dropping the tool may cause an
accident.
22. Do not use the tool for any work other than
wire tying. Otherwise, an accident may occur.
23. Always use Makita's genuine wires. If wires are
not used for a long period of time, they may
rust. Do not use rusted wires. Otherwise, they
may cause an accident.
24. After tying, check for wire breakage due to
excessive twisting. If any wires are broken,
tying strength will be lost. Adjust the tying
strength, and tie the rebars again.
25. Securely place the arm against the rebars. If
it is not securely positioned, a clearance will be
created between the rebars, and tying strength will
be compromised.
Symbols
The followings show the symbols used for tool.
volts
direct current
Keep hands away from the tool tip.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery char-
ger, (2) battery, and (3) product using battery.
Do not disassemble or tamper with the battery
2.
cartridge. It may result in a fire, excessive heat,
or explosion.
If operating time has become excessively
3.
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water or rain.
A battery short can cause a large current flow, over-
heating, possible burns and even a breakdown.
6. Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8. Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the
battery cartridge. Such conduct may result in a
fire, excessive heat, or explosion.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject to
the Dangerous Goods Legislation requirements.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consulting an
expert for hazardous material is required. Please also
observe possibly more detailed national regulations.
Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move
around in the packaging.
5 ENGLISH