Baratza Encore - Coffee Grinder Quick Start Guide

Also See for Encore:

Quick start manual (25 pages)

Operation manual (18 pages)

How-to (10 pages)

Table of Contents

Contents

1 Parts Identification
2 INITIAL SETUP
3 CHOOSING A GRIND SETTING
4 SAFETY INFORMATION
5 Documents / Resources
- 5.1 References
- 5.2 Download manual

Baratza Encore - Coffee Grinder Quick Start Guide

Parts Identification

Hopper Lid
Bean Hopper
Grind Setting Indicator
Hopper Gasket
Removable Ring Burr
Grind Settings
Pulse Button
Grounds Bin with Max Fill Line
On/Off Knob *
Brush *
Weighted Base
Grind Adjustment Ring
Grind Adjustment Tab
Burr Lifting Tabs
Wingnut (do not remove)
Center Cone Burr

* included in grounds bin

INITIAL SETUP

For the full manual, visit baratza.com/documentation

Remove the contents from the packaging and hand-wash the hopper lid (1), bean hopper (2), and grounds bin (8) in warm, soapy water. Let air dry. Do not wash the ring burr (5) in water or it will rust.
To install the hopper, align the silver grind setting indicator (3) with the triangle near grind setting 40 (6). Press the hopper down and twist clockwise into place. The grinder will not start without the hopper installed.*
To install the on/off knob (9), align it with the stem of the switch on the right side of the unit and press into place. Use either the on/off knob or the pulse button (7) to begin grinding.

*If there is difficulty in installing the hopper: Ensure that the ring burr (5) is fully seated in place. The grind adjustment ring (12) must be rotated fully counterclockwise using the grind adjustment tabs (13) for the hopper to be installed. When grinding into the grounds bin, coffee tends to mound up. To prevent clogging, empty the grounds before they reach the max fill line.

CHOOSING A GRIND SETTING

Finer Grind = lower numbers
Coarser Grind = higher numbers

Rotate the hopper to adjust to the desired grind setting. When adjusting the grind setting, the grinder must be running or completely empty of beans to prevent damage to the grinder. Below are suggested starting points for what grind settings to use for common brew methods. Coarser or finer grinding may be needed depending on recipe requirements and taste preference.

Additional information can be found at baratza.com/grinding-tips

	Espresso	AeroPress	Hario V60	Automatic Brewer	Chemex	French Press
Suggested Setting	8	12	15	18	20	28

IF YOU NEED FURTHER SUPPORT:

In US & Canada contact
Support@baratza.com
or 425-641-1245
or toll free 877-701-2021

If you think your grinder is not performing correctly, go to our troubleshooting guides at baratza.com/troubleshooting
Outside North America, the warranty is provided by the company you purchased from. For service, find the nearest importer at baratza.com/international-importers-and-retailers

SAFETY INFORMATION

Please read the information below very carefully. It contains important safety information for this appliance. Please keep these instructions for future reference.

Use only with AC current and the correct voltage. See the label on the base of the grinder to determine the correct voltage.
Only clean the grinder housing with a dry or slightly damp cloth. Do not immerse the grinder, plug or cord in water or any other liquid.
Baratza will not accept any liability for damage, injury, or warranty if the grinder is used other than for its intended purpose (i.e. grinding roasted whole coffee beans) or is improperly operated or repaired.
Do not operate the grinder with a damaged cord or plug. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Keep the appliance and its cord out of reach of children aged less than 8 years.
Do not leave your grinder unattended while turned ON.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Cleaning and user maintenance shall not be made by children without supervision.
Always unplug the grinder from the electrical supply before assembling, disassembling or cleaning. To unplug, grasp plug and remove from the outlet. Never pull on the cord.
ALWAYS unplug the electrical supply cord prior to cleaning the grinder.