Baratza Encore How-To
Power cord replacement
Hide thumbs
Also See for Encore:
- Quick start manual ,
- Operation manual (18 pages) ,
- Service manual (7 pages)
Advertisement
Quick Links
How to: Power Cord Replacement
Encore, Virtuoso, Preciso, Virtuoso+
Time: 25 min
Difficulty: Medium
Tools/supplies: Flat head screwdriver. T10 screwdriver. Phillips screwdriver. Pick. Pliers (optional)
Parts: US Power Cord (SKU 6300)
Additional Resources: Circuit Board Replacement. Timer Switch Replacement. On-Off Switch Re-
placement. Case Removal.
Flat
Phillips
www.baratza.com
*** Unplug the grinder from power supply ***
Remove the case using the Case Removal guide.
If your unit has an on-off switch,
an additional wire is required
which you can request directly.
Torx-10
Pliers
Pick
OPTIONAL: label wires with tape
or stickers before proceeding for
ease of reassembly
support@baratza.com
US Power Cord (SKU: 6300)
ver. 1.0
rev. 6/5/2019
Advertisement
Related Manuals for Baratza Encore
Summary of Contents for Baratza Encore
- Page 1 1.0 How to: Power Cord Replacement Encore, Virtuoso, Preciso, Virtuoso+ Time: 25 min Difficulty: Medium Tools/supplies: Flat head screwdriver. T10 screwdriver. Phillips screwdriver. Pick. Pliers (optional) Parts: US Power Cord (SKU 6300) Additional Resources: Circuit Board Replacement. Timer Switch Replacement. On-Off Switch Re- placement.
- Page 2 These screws may be Phillips or Torx size 10. If you do not have Torx, use 2mm hex. Lift the motor/gearbox assembly out of the chassis and unplug the grinder from the board. www.baratza.com support@baratza.com rev. 6/5/2019...
- Page 3 Unplug the power cord connector from the circuit board. Unplug the cables leading to the timer or on/off switch. For units with on/ off switch, press into terminal to release wires. See On-Off Switch Replacement guide for clarification www.baratza.com support@baratza.com rev. 6/5/2019...
- Page 4 Remove the four feet at the base of the unit to expose screws. Remove the four base screws to separate the base from the chassis. www.baratza.com support@baratza.com rev. 6/5/2019...
- Page 5 Push the strain relief down to lock the retaining clip in a disengaged position. Repeat on the other two releases until the strain relief removes entirely. www.baratza.com support@baratza.com rev. 6/5/2019...
- Page 6 Using a flat head screwdriver, push in and down to release the clip and open the strain relief. Position the strain relief on the new cord and squeeze shut (pliers may be needed). OPTIONAL OPTIONAL www.baratza.com support@baratza.com rev. 6/5/2019...
- Page 7 The replacement will only have one wire installed to the connector. There are two other wires which must be installed. Encore Virtuoso To remove the cables from the old connector, insert a narrow tool into the exposed slot and pull gently on the related cable.
- Page 8 Connect the long black wire to the interlock switch. Return the circuit board by securing the two mounting screws. Plug the power cord connector into the circuit board. www.baratza.com support@baratza.com rev. 6/5/2019...
- Page 9 *for wiring reference, see On-Off Switch replacement guide* Install the base, 4 screws and 4 feet. Install the gearbox/ motor assembly and plug the motor cable into the board. www.baratza.com support@baratza.com rev. 6/5/2019...
- Page 10 Reinstall the case and knob to return the grinder Ensure that to operation. wires are firmly connected, and actuator faces inward. If you encounter any issues or have questions about this guide, contact support@baratza.com www.baratza.com support@baratza.com rev. 6/5/2019...