Table of Contents
Advertisement
Quick Links
TURBO HD
D8T Series Bullet Camera
User Manual
UD05328B
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Type
Type I
Camera
Type II
Camera
This manual may contain several technical incorrect
places or printing errors, and the content is subject to
change without notice. The updates will be added to
the new version of this manual. We will readily improve
or update the products or procedures described in the
manual.
Model
DS-2CE16D8T-IT(E)
DS-2CE16D8T-ITP
DS-2CE16D8T-IT1(E)
DS-2CE16D8T-IT3(E)
DS-2CE16D8T-IT5(E)
0100001070415
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-2CE16D8T-IT1
Summary of Contents for HIKVISION DS-2CE16D8T-IT1
- Page 1 This manual applies to the models below: Type Model DS-2CE16D8T-IT(E) Type I Camera DS-2CE16D8T-ITP DS-2CE16D8T-IT1(E) Type II DS-2CE16D8T-IT3(E) Camera DS-2CE16D8T-IT5(E) This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual.
- Page 2 Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
- Page 3 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected.
-
Page 4: Product Features
1 Introduction 1.1 Product Features The camera is applicable for both indoor and outdoor conditions, and the application scenarios include road, warehouse, underground parking lot, bar, etc.. The main features are as follows: High performance CMOS sensor Low illumination, 0.005 Lux @ (F2.0, AGC ON), 0 Lux ... -
Page 5: Installation
2 Installation Before you start: Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the ... - Page 6 Connect the corresponding power cord, and video cable. Power on the camera to check whether the image on the monitor is gotten from the optimum angle. If not, adjust the camera according to the figure below to get an optimum angle. Pan Position [0°...
- Page 7 6. Secure the junction box’s body with supplied screws on the ceiling/wall. Junction Box Body Fix the Junction Box to the Wall/Ceiling Figure 2-6 7. Route the cables through the bottom cable hole, or the side cable hole of the junction box. 8.
-
Page 8: Ceiling/Wall Mounting With Junction Box
Fix the Camera to the Ceiling Figure 2-9 Note: The supplied screw package contains self-tapping screws, and expansion bolts. For cement wall/ceiling, expansion bolts are required to fix the camera. For wooden wall/ceiling, self-tapping screws are required. 5. Connect the corresponding power cord, and video cable. - Page 9 Install the Junction Box Figure 2-11 Route the cables through the bottom cable hole, or the side cable hole of the junction box. 7. Combine the junction box cover with its body with supplied screws on the junction box’s cover. Combine the Junction Box’s Cover with its Figure 2-12 Body...
-
Page 10: Menu Description
3 Menu Description Purpose: Call the menu by clicking button on the PTZ Control interface, or call preset No.95. Steps: 1. Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1. TVI DVR Camera Monitor Connection Figure 3-1 2. - Page 11 3.2 LANGUAGE Supports English, and Chinese. 3.3 MAIN MENU 3.3.1 AE (AUTO EXPOSURE) Auto Exposure describes the brightness-related parameters, which can be adjusted by BRIGHTNESS, EXPOSURE MODE, AGC, and SENSE UP. Figure 3-3 BRIGHTNESS Brightness refers to the brightness of the image. You can set the brightness value from 1 to 10 to darken or brighten the image.
-
Page 12: Video Setting
ATW (Aoto Tracking White Balance) Under ATW mode, white balance is being adjusted automatically according to the color temperature of the scene illumination. MWB (Manual White Balance) You can set the R GAIN/B GAIN value from 1 to 255 to adjust the shades of red/blue color of the image. - Page 13 CONTRAST This feature enhances the difference in color and light between parts of an image. You can set the CONTRAST value from 1 to 10. SHARPNESS Sharpness determines the amount of detail an imaging system can reproduce. You can set the SHARPNESS value from 1 to 10.
-
Page 14: Save And Exit
position and size of the area. Set the SENSITIVITY from 0 to 100. CAMERA ID Edit the camera ID on this section. CAM ID SETTING Figure 3-9 Set the MODE as on. Click up/don left/right button to choose the camera ID and the position. 3.3.6 RESET Reset all the settings to the default.