TURBO HD D8T Series Dome Camera User Manual User Manual Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer. This manual applies to the models below: Type Model Type I Camera...
Page 2
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Page 3
Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected.
1 Introduction 1.1 Product Features The main features are as follows: High performance CMOS sensor IR cut filter with auto switch OSD menu with configurable parameters Auto white balance Internal synchronization SMART IR mode 3-axis adjustment ...
2 Installation Before you start: Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the ...
Page 6
Figure 2-3 Secure the Back Box 5. Attach the camera to the back box and secure them with supplied screws. Figure 2-4 Attach the Camera Note: The supplied screw package contains self-tapping screws, and expansion bolts. For cement wall/ceiling, expansion bolts are ...
Page 7
10. Tighten the screws on the bubble of the dome camera to finish the installation. Figure 2-7 Finish Installation 2.2 Ceiling Mounting of Type II Camera Steps: 1. Disassemble the bubble by anti-clockwise rotating the camera. Figure 2-8 Disassemble the Camera 2.
Page 8
For cement wall/ceiling, expansion bolts are required to fix the camera. For wooden wall/ceiling, self-tapping screws are required. 5. Route the cables through the cable hole, or the side opening. 6. Secure the camera on the adapter plate. Figure 2-11 Secure the Camera 7.
Page 9
Steps: 1. Paste the dill template to the ceiling. 2. Drill the screw holes and cable hole (optional) in the ceiling according to the drill template. Figure 2-15 Drill Template Note: Cable hole is required, when adopting the ceiling outlet to route cables. 3.
Page 10
Figure 2-18 3-Axis Adjustment 8. Adjust the tilt position [0° to 75°], the pan position [0° to 355°], the rotation position [0° to 355°]. 9. Install the bubble back to the camera. Figure 2-19 Install the Bubble Back 10. Tighten the screws on the bubble of the dome camera to finish the installation.
3 Menu Description Please follow the steps below to call the menu. Steps: 1. Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1. Figure 3-1 Connection 2. Power on the analog camera, TVI DVR, and the monitor to view the image on the monitor.
(1) Click up/down direction button to select the item. (2) Click Iris + to confirm the selection. (3) Click left/right direction button to adjust the value of the selected item. 3.1 VIDOE FORMAT When switching the video output as CVBS, you can ...
Page 13
frame, which makes a camera more sensitive to the light so it can produce images even in low lux conditions. You can set the SLOW SHUTTER function as OFF, x2, x4, x6, x8, x10, x12, x14, or x16 according to the different light conditions.
You can turn on/off the IR LIGHT to meet the requirements of different circumstances. SMART IR The Smart IR function is used to adjust the light to its most suitable intensity, and prevent the image from over exposure. You can select the mode as MODE 1, or MODE 2. MODE 1 is the default mode that can be applied to both indoor conditions, and outdoor conditions.
WHITE BALANCE MANUAL MODE R-GAIN B-GAIN BACK EXIT SAVE & EXIT Figure 3-7 MANUAL MODE BRIGHTNESS Brightness refers to the brightness of the image. You can set the brightness value from 1 to 9 to darken or brighten the image. The higher the value is, the brighter the image is.
MOTION DET Figure 3-8 MOTION Select a MOTION area. Set the MODE as ON. Click the up/down/left/right button to define the position, and the size of the area. Set the SENSITIVITY from 1 to 9. PRIVACY The privacy mask allows you to cover certain areas which you don’t want to be viewed, or recorded.