Table of Contents
Advertisement
Quick Links
TURBO HD
D8T Series Dome Camera
User Manual
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Type
Type I
Type II
This manual may contain technical incorrect places or
printing errors, and the content is subject to change
without notice. The updates will be added to the new
version of this manual. We will readily improve or
update the products or procedures described in the
manual.
Model
DS-2CE5AD8T-AVPIT3Z
DS-2CE5AD8T-VPIT3ZE
0100001080310
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-2CE5AD8T-AVPIT3Z
Summary of Contents for HIKVISION DS-2CE5AD8T-AVPIT3Z
- Page 1 This manual applies to the models below: Type Model Type I DS-2CE5AD8T-AVPIT3Z Type II DS-2CE5AD8T-VPIT3ZE This manual may contain technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual.
-
Page 2: Regulatory Information
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. - Page 3 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected.
- Page 4 Keep the camera away from liquid while in use for non-water-proof device. While in delivery, the camera shall be packed in its original packing, or packing of the same texture. Mark Description Table 0-1 Mark Description Mark Description DC Voltage AC Voltage 1 Introduction...
-
Page 5: Installation
2 Installation Before you start: Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the ... - Page 6 Figure 2-3 Attach the Back Box Note: The supplied screw package contains self-tapping screws, and expansion bolts. For cement ceiling, expansion bolts are required to fix the camera. For wooden ceiling, self-tapping screws are required. 5. Route the cables through the cable hole, or the side opening.
- Page 7 Steps: 1. Drill 4 screw holes in the wall according to the holes of the mount. 2. Attach the mount to the wall by aligning the 4 screw holes of the mount with expansion screws on the wall. 3. Secure the mount with 4 hex nuts and washers. Figure 2-7 Install Wall Mount 4.
-
Page 8: Menu Description
3 Menu Description Purpose: Call the menu by clicking button on the PTZ interface, or call preset No.95. Steps: 1. Connect the camera with the TVI DVR, and the monitor shown as the Figure 3-1. Figure 3-1 Connection 2. Power on the analog camera, TVI DVR, and the monitor to view the image on the monitor. - Page 9 3.3 FOCUS Move the cursor to FOCUS, and press the Iris+ to enter the submenu. Click FOCUS+, FOCUS-, ZOOM+, and ZOOM- to adjust the focus. 3.4 MAIN MENU 3.4.1 AE (AUTO EXPOSURE) Auto Exposure describes the brightness-related parameters, which can be adjusted by BRIGHTNESS, EXPOSURE MODE, AGC, and SENSE UP.
-
Page 10: Video Setting
the environment. It can remove unrealistic color casts in the image. You can set WB mode as ATW, or MWB. ATW (Aoto Tracking White Balance) Under ATW mode, white balance is being adjusted automatically according to the color temperature of the scene illumination. - Page 11 CONTRAST This feature enhances the difference in color and light between parts of an image. You can set the CONTRAST value from 1 to 10. SHARPNESS Sharpness determines the amount of detail an imaging system can reproduce. You can set the SHARPNESS value from 1 to 10.
-
Page 12: Save And Exit
position and size of the area. Set the SENSITIVITY from 0 to 100. CAMERA ID Edit the camera ID on this section. CAM ID SETTING MODE CAM ID X POSITION 75 Y POSITION RETURN Figure 3-9 CAM ID SETTING Set the MODE as on.