Specifications; Standard Equipment - RIDGID K-4310 FXP Manual

K-4310 FXP Drum Machine
XXXXXMMYY
Figure 6 – Machine Serial Number - The last 4 digits of
the serial number indicate the month and year
of the manufacture

Specifications

Drain Line
Capacity ............See Following Chart
Cable Line Size
Size
5/8" 3" to 6" (75 mm
(16mm) to 150 mm)
3/4" 4" to 10" (100
(20mm) mm to 250 mm)
See RIDGID catalog for information on specific cables
available.
Drain
Capacity ............3" to 10" (75mm to 250mm)
Drum Capacity,
5/8" Drum ..........100' (30.5m) of
Cable
Drum Capacity,
3/4" Drum ..........125' (38.1m) of
Cable
100' (30.5m) of
Cable
100' (30.5m) of ¾" (20mm) Diameter
Cable
Power Supply ....RIDGID RB-FXPXX Battery Pack OR
FXP Power Adapter (See Optional
Equipment Section)
Motor Type .........Brushless DC
Watts .................810 W
Voltage ..............54V DC nominal
Amps .................15 A
No Load Output
Speed ................240 RPM
Controls .............Main ON-OFF Switch, FOR/OFF/REV
Switch, Pneumatic Foot Switch,
AUTOFEED
8
Maximum Maximum AUTO-
Reach FEED Unit Speed
250' (61m) 25'/Min (7.6 m/min)
250' (61m) 28'/Min (8.5 m/min)
/ " (16mm) Diameter
5
8
/ " (16mm) Diameter
5
8
/ " (17 .5mm) Diameter
11
16
Cable Feed Unit Lever
®
Operating
Temperature ......-4° F to 140° F (-20° C to 60° C)
Storage
Temperature ......-4° F to 140° F (-20° C to 60° C)
Wireless Connection
Range ................33 ft (10 m)
Memory .............50 Job Recordings (1 Job is approxi-
mately 2 hours)
Cable Travel
Tolerance ...........+/- 2 ft (+/- 0.6 m)**
Frame Type .......Wheeled Cart
Weight (No Cable, 3/4" Drum w/pigtail and AUTOFEED
Unit) ...................125 lbs. (63.5 kg)
Weight (w/100' of 3/4" Cable and AUTOFEED
Unit) ...................235 lbs. (113 kg)
Weight (w/100' of 5/8" Cable and AUTOFEED
Unit) ...................193 lbs. (87 .5 kg)
Dimension LxWxH (no AUTOFEED Unit, Handle
down).................34" x 22" x 35"
(864mm x 559mm x 889mm)
Dimension LxWxH (w/AUTOFEED Unit, Handle
up) .....................37" x 22" x 47"
(940mm x 559mm x 1194mm)
Sound Pressure
(L )* ..................84.5 dB(A), K=3
PA
Sound Power
(L )* .................85.09 dB(A), K=3
WA
* Sound measurements are measured in accordance with a standardized test per
Standard EN 62481-1.
- Sound emissions may vary due to your location and specific use of these tools.
- Daily exposure levels for sound need to be evaluated for each application and
appropriate safety measures taken when needed. Evaluation of exposure lev-
els should consider the time a tool is switched off and not in use. This may
significantly reduce the exposure level over the total working period.
** Cable Travel Tolerance – this tolerance assumes that the correct cable pa-
rameters are entered (cable diameter, cable length and drum) and that the full
cable length is in the drum (the cable end is no more than 6" (150 mm) out of
the end of the AUTOFEED cable feed unit) when the cable travel is zeroed.
Incorrect cable parameters and zeroing the cable travel with cable out of the
drum results in a greater cable travel tolerance, in some cases up to +/- 8 ft
(+/-2.5m). Cable travel does not necessarily equal distance the cable end has
traveled in the drain.

Standard Equipment

All K-4310 FXP Drum Machines comes with one pair of
RIDGID Drain Cleaning Gloves. Refer to the RIDGID cata-
log for details on equipment supplied with specific machine
catalog numbers.
This machine is made to clean drains. If prop-
NOTICE
erly used it will not damage a drain that is in good condi-
tion and properly designed, constructed and maintained.
If the drain is in poor condition, or has not been properly
designed, constructed and maintained, the drain cleaning
process may not be effective or could cause damage to the
drain. The best way to determine the condition of a drain
999-995-420.10_REV A