Blower Operation - Makita UB402MP Original Instruction Manual

Installing the end nozzle
Align the protrusion on the blower pipe with the groove
on the end nozzle, then attach the end nozzle to the
blower pipe, and then turn the end nozzle to lock it into
place.
► Fig.9: 1. Triangle mark 2. End nozzle 3. Blower pipe
To remove the end nozzle, perform the installation
procedure in reverse.
NOTE: The length of the nozzle can be changed by
moving the nozzle as shown in the figure.
► Fig.10
Installing the flat nozzle or
extension nozzle
Optional accessory
1.
Remove the end nozzle from the attachment.
2.
Attach the flat nozzle or extension nozzle to the
attachment, and then turn it to lock it into place.
► Fig.11: 1. Flat nozzle 2. Extension nozzle
3. Attachment
Installing the gutter nozzle set
Optional accessory
1. Remove the end nozzle, extension nozzle, or flat
nozzle from the attachment.
2. Loosen the screw on the small hose clamp, and
pass the hose clamp through the attachment.
► Fig.12: 1. Screw 2. Hose clamp (small)
3. Attachment
3. Connect the extension pipe to the attachment.
Align the groove on the extension pipe with the protru-
sion on the attachment, and then slide the extension
pipe along its groove so that the triangle markings face
each other.
► Fig.13: 1. Extension pipe 2. Attachment
4.
Place the hose clamp onto the groove as illus-
trated and tighten the screw.
► Fig.14: 1. Screw 2. Hose clamp
5. According to the working height, connect the rest
of extension pipes to the extension pipe which has
already been attached.
CAUTION:
When using the gutter nozzle set
in conjunction with a multi function power head
and blower attachment, do not use three or more
extension pipes. It may cause imbalance and result
in injury.
6. Turn the outlet of the end nozzle as shown in the
figure.
► Fig.15
7. Connect the end nozzle to the extension pipe.
When connecting, align the triangle marking on the end
nozzle and the extension pipe, and then push the end
nozzle until it clicks. After that, rotate the end nozzle to
a suitable position for your work.
► Fig.16: 1. End nozzle 2. Extension pipe 3. Triangle
marking
When removing the end nozzle, align the triangle mark-
ings on the end nozzle and extension pipe, and then
pull out the end nozzle from the extension pipe.
► Fig.17: 1. End nozzle 2. Extension pipe 3. Triangle
marking
OPERATION
WARNING:
tions in the chapter "SAFETY WARNINGS" and
the instruction manual of the power unit.
WARNING:
shoulder harness to your comfortable position
before operating.

Blower operation

CAUTION:
Do not place the machine on the
ground while it is switched on. Sand or dust may
enter from suction inlet and cause a malfunction or
personal injury.
Hold the machine firmly with both hands and perform
the blowing operation by moving it around slowly. When
blowing around building, big stone or vehicle, direct the
nozzle away from them. When performing an operation
in a corner, start from the corner and then move to wide
area.
Adjust the air speed with the switch trigger of the power
unit according to the environment or conditions of your
usage.
► Fig.18
Using the gutter nozzle set
CAUTION:
When using the gutter nozzle set,
do not hold the blower with single hand but with
both hands.
► Fig.19
CAUTION:
Do not use the gutter nozzle set
near electric wires.
► Fig.20
CAUTION:
Do not use the gutter nozzle set on
windy day.
► Fig.21
CAUTION:
When using the gutter nozzle set,
keep other people or animal more than 15 m away
from the blower.
► Fig.22
11 ENGLISH
Follow the warnings and precau-
Adjust the hanger position and