Error Code; Memory Function; Maintenance - Makita CW002G Instruction Manual

• Over- voltage protection
W hen the input voltage is higher than the rated
oltage, this protection system turns o the
appliance and the temperature display sho w s " F4 "
w ith beep sound.
• Tilt protection function
The tilt protection function is valid w hen operating
the appliance in cooling mode. W hen the
appliance get e q ual to or greater than 30° from
le el angle as sho n A, B, C, or D in the figure,
the appliance stops cooling and the temperature
display sho w s "F1" for a w hile. After the appliance
back in level position , it takes about 3 minutes to
restart.
► Fig.4
Protections against oth er causes
P rotection system is also designed for other causes that
could damage the appliance and allo w s the appliance to
stop automatically. Take all the follo w ing steps to clear
the causes , w hen the appliance has been brought to a
temporary halt or stop in operation.
urn the appliance o , and then turn it on again to
restart.
2. C harge the battery(ies) or replace it/them w ith
recharged battery(ies).
3. Let the appliance and battery(ies) cool do w n.
If no improvement can be found by restoring protection
system , then contact your local Makita Service C enter.
USB ch arging
There is the U SB port in the battery compartment. The
U SB port continuously outputs 5V voltage in operation
state.
NOTICE:
C onnect only devices w h ic h are
compatible w it h t h e USB po w er supply port.
Other w ise it may cause malfunction to the appliance.
NOTICE:
D o not connect t h e USB po w er supply
port of t h is appliance to t h e USB terminal of your
computer. It may cause malfunction.
NOTICE:
Before connecting USB device to
t h e appliance , al w ays backup your data of USB
device. Other w ise your data may be lost by any
possibility.
NOTICE:
W h en not using devices or after
c h arging , remove t h e USB cable.
NOTE: The appliance may not supply po w er to some
U SB devices.

Memory function

After setting the control temperature , if the user does
not operate w ithin 5 seconds , the current setting w ill be
memori z ed. Ne x t time , the appliance starts in the same
setting.
Sw itch ing th e unit of temperature
Y ou can s w itch the unit of temperature ° C (degree
C elsius) or °F (degree Fahrenheit) by follo w ing
procedure.
1. Turn on the appliance.
2. P ress the cool / heat s w itch button until the unit
C or starts ashing
3. P ress the temperature plus button or the
temperature reduction button to select unit.
4. P ress the cool / heat s w itch button , or leave the
appliance 5 seconds w ithout any operation. The
unit selection is completed.

Error code

or the specific errors, the temperature display sho s
follo w ing code.
Error code
F1 Tilt protection is active. Refer the section for
the tilt protection function.
F2 Running out of battery.
F3 Input voltage is low . Refer the paragraph for
the low -voltage protection.
F4 Input voltage is high. Refer the paragraph for
the over-voltage protection.
Error codes urn o and restart the appliance
other than still does not improve, take the appliance to
the above Makita Authoriz ed or Factory Service C enters.
MAINTENAN C E
CAUTION:
Al w ays be sure t h at t h e appliance
is switched off, unplugged, and the battery
cartridge is removed before attempting to perform
inspection or maintenance.
CAUTION:
D o not spray or pour w ater on
t h e appliance w h en cleaning. D o not w as h w it h a
h ose ; avoid getting w ater inside of t h e appliance.
NOTICE:
Never use gasoline , ben z ine , t h inner ,
alco h ol or t h e like. D iscoloration , deformation or
cracks may result.
To maintain product SAFET Y and RELIABILIT Y ,
repairs, any other maintenance or ad ustment should
be performed by Makita Authori z ed or Factory Service
C enters , al w ays using Makita replacement parts.
C leaning
• C lean the oil stain in the chamber regularly.
• C lean around the interior of the chamber to
prevent odor.
Clean the dust on the sponge filter regularly to
impro e the re rigeration e ciency
• The sealing strip of the upper cover is easy to get
dirty , clean it in time.
1 1 E N G L IS H
Matter
the error