Autofeed Assembly; Instructions For Mounting Autofeed To K-39/K-39B; Machine Inspection - RIDGID K-39 Series Operator's Manual

K-39/K-39B Drain Cleaning Machine
Catalog Model
No. No. Description
68057 K-39 K-39 Drain Cleaner
C-1IC Cable w/Bulb Auger (
68137 K-39B K-39B Cordless Drain Cleaner, BP12 Battery
Pack, BC12 Charger, C-1 Cable w/Bulb
Auger ( 5 /
68062 K-39-1 Same as Model No. K-39 plus:
C-6429 Carrying Case
68172 K-39C-1 K-39-1 with 3 Jaw chuck rather than slide
action chuck
68142 K-39B-1 Same as Model No. K-39B plus:
(1) additional BP12 Battery Pack
C-6429 Carrying Case
68067 K-39-5 K-39 Drain Cleaner
C-1IC Cable w/Bulb Auger (
C-6 Cable w/
A-13 Pin Key
T-203 Bulb Auger
T-205 "C" Cutter
T-210 Grease Cutter
T-217 Drop Head Auger
C-6429 Carrying Case
68072 K-39-7 K-39 Drain Cleaner
C-1IC Cable w/Bulb Auger (
C-6 Cable w/
C-21 Cable w/Bulb Auger (
A-13 Pin Key
T-203 Bulb Auger
T-205 "C" Cutter
T-210 Grease Cutter
T-217 Drop Head Auger
C-6429 Carrying Case
68082 K-39PF K-39 Drain Cleaner
C-1IC Cable w/Bulb Auger (
Autofeed
68087 K-39PF-1 K-39-1 with Autofeed
68092 K-39PF-5 K-39-5 with Autofeed
68187 K-39PF-7 K-39-7 with Autofeed
68147 K-39B-PF-1 K-39B-1 with Autofeed
Table 1 – Equipment Available with Standard Models

Autofeed Assembly

WARNING
To prevent serious injury, proper assembly of the
Drain Cleaner is required. The following proce-
dures should be followed:
Instructions For Mounting Autofeed To
K-39/K-39 Battery
NOTE! Autofeed attachment can only be mounted on a
K-39 with slide-action chuck.
NOTE! Removal of parts is not required to attach the
autofeed assembly.
5 / " x 25')
16
" x 25')
16
5 / " x 25')
16
5 / " Coupling ( 3 / " x 35')
8 8
5 / " x 25')
16
5 / " Coupling ( 3 / " x 35')
8 8
5 / " x 50')
16
5 / " x 25')
16
Ridge Tool Company
1. Lift up the feed actuator lever to expose the screw
hole in the hand grip. It should require effort to lift the
handle (Figure 3).
Figure 3 – Mounting Autofeed
2. Slide autofeed unit over the cable and align it with the
hand grip of the K-39.
3. Secure the autofeed unit with the four (4) screws
provided. Tighten screws snugly. DO NOT OVER-
TIGHTEN. The slotted holes are for convenience
only and can be aligned as desired.
4. Push the feed actuator lever back down into its
locked position.
Drain Cleaner Inspection
WARNING
To prevent serious injury, inspect your Drain
Cleaning Machine. The following inspection pro-
cedures should be performed before each use.
1. Make sure the Drain Cleaning Machine is unplugged.
2. Electrical components:
K-39 Drain Cleaner:
Inspect the power cord and plug for damage. If the
plug has been modified or if the cord is damaged, do
not use the Drain Cleaner until the cord has been re-
placed.
K-39 Battery Charger:
Inspect the power cord and plug for damage. If the
cord or plug is damaged, do not use the charger
until the cord is replaced. Inspect charger for damage.
Do not use charger if it has received a sharp blow,
been dropped or otherwise damaged.
5