Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita TD110DWY
Summary of Contents for Makita TD110DWY
- Page 1 INSTRUCTION MANUAL Cordless Cutter CC301D Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: CC301D Diamond wheel diameter 85 mm Max. wheel thickness 0.8 mm Max. Cutting depth at 0° bevel 25.5 mm at 45° bevel 16.5 mm Rated speed 1,600 min Rated voltage D.C. 10.8 V - 12 V max Battery cartridge BL1015, BL1016, BL1020B, BL1040B, BL1041B BL1021B... - Page 3 Work area safety If devices are provided for the connection of dust extraction and collection facilities, ensure Keep work area clean and well lit. Cluttered or these are connected and properly used. Use of dark areas invite accidents. dust collection can reduce dust-related hazards. Do not operate power tools in explosive atmo- spheres, such as in the presence of flammable Power tool use and care...
- Page 4 Hold the power tool by insulated gripping Cordless cutter safety warnings surfaces only, when performing an operation where the cutting accessory may contact hid- The guard provided with the tool must be den wiring. Cutting accessory contacting a “live” securely attached to the power tool and wire may make exposed metal parts of the power positioned for maximum safety, so the least tool “live”...
- Page 5 WARNING: DO NOT let comfort or familiarity also void the Makita warranty for the Makita tool and with product (gained from repeated use) replace charger. strict adherence to safety rules for the subject product.
-
Page 6: Functional Description
Battery protection system FUNCTIONAL DESCRIPTION The tool is equipped with a battery protection system. This system automatically cuts off power to the motor to extend battery life. CAUTION: The tool will automatically stop during operation if the Always be sure that the tool is tool and/or battery are placed under one of the following switched off and the battery cartridge is removed conditions:... -
Page 7: Bevel Cutting
Set for the desired angle (0° - 45°) wheel by tilting accordingly, then tighten the clamping screw securely. CAUTION: Sighting Use only the Makita wrench to install or remove the diamond wheel. CAUTION: When installing the diamond wheel, be sure to tighten the bolt securely. CAUTION:... - Page 8 Hex wrench storage ► 1 . Shaft lock 2. Hex wrench 3. Tighten 4. Loosen ► 1 . Hex wrench When not in use, store the hex wrench as shown in the figure to keep it from being lost. Installing water supply Loosen the screw A. Slide the tank holder all the way over the motor housing so that the notch of the band (part of the tank holder) is posi- tioned just below the screw head of the tool as illustrated.
-
Page 9: Water Supply
Water supply OPERATION CAUTION: When filling the tank with water, be CAUTION: This tool should only be used on careful not to let the tool get wet. horizontal surfaces. Be sure that the water supply cock is closed before CAUTION: Be sure to hold the workpiece filling the tank with water. Open the cap on the tank and firmly down on a stable bench or table during... -
Page 10: Maintenance
Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. - Page 12 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885502B221 www.makita.com 20171010...