Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Draytek VigorAP 960C
Summary of Contents for Draytek VigorAP 960C
- Page 2 VigorAP 960C 802.11ax Ceiling-mount Access Point Quick Start Guide Version: 1.0 Firmware Version: V1.3.8 (For future update, please visit DrayTek web site) Date: December 02, 2020...
- Page 3 Intellectual Property Rights (IPR) Information © All rights reserved. This publication contains information that is protected Copyrights by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. The following trademarks are used in this document: Trademarks Microsoft is a registered trademark of Microsoft Corp.
- Page 4 Declaration of Conformity Hereby, DrayTek Corporation declares that the radio equipment type VigorAP 960C is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.draytek.com.tw/ftp/VigorAP 960C/Document/CE/ Manufacturer: DrayTek Corp.
- Page 5 12.0W 18.0W H Average active efficiency 83.3% 85.5% I Efficiency at low load 10% 80.8% 83.7% J No-load power consumption 0.06W 0.07W *The external power supply used for each product will be model dependent. For more update, please visit www.draytek.com.
-
Page 6: Table Of Contents
1. Package Content ....................1 2. Panel Explanation....................2 3. Installation......................3 3.1 Ceiling-mount Installation (Wooden Ceiling) ................3 3.2 Ceiling-mount Installation (Plasterboard Ceiling)............... 4 3.3 Suspended Ceiling (Lightweight Steel Frame) Installation............5 3.4 Wall-Mounted Installation ......................7 4. Connection and Configuration ................8 4.1 Notifications for Hardware Connection.................. -
Page 7: Package Content
Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. VigorAP 960C Main Unit Ceiling mount bracket & Quick Start Guide T-Rail Mounting Kits Fixings and Screws (Used for suspended ceiling) -
Page 8: Panel Explanation
Factory Reset Ethernet Port Power Jack (DC IN) Status Explanation Blue LED The system is in boot-loader mode. The system is not ready or fails. Blinking The system is in AP mode and work normally. Green LED Blinking The system is in Mesh mode or Range Extender mode and works normally. -
Page 9: Installation
VigorAP can be installed under certain locations: wooden ceiling, plasterboard ceilings, light-weighted steel frame and wall. Place the bracket under the wooden ceiling and fasten two screws firmly (as shown in Figure below, Step 1). When the bracket is in place, fasten two screws firmly (as shown in Figure below, Step 2) on the bottom of VigorAP. -
Page 10: Ceiling-Mount Installation (Plasterboard Ceiling)
Place the bracket under the plasterboard ceiling and fasten two turnbuckles firmly (as shown in Figure below, Step 1). Make the screws pass through the bracket and insert into the turnbuckles (as shown in Figure below, Step 2). Fasten them to offer more powerful supporting force. -
Page 11: Suspended Ceiling (Lightweight Steel Frame) Installation
You cannot screw into ceiling tiles as they are weak and not suitable for bearing loads. Your VigorAP is supplied with mounts (T-Rail brackets) which attach directly to the metal grid (‘T-Rail’) of your suspended ceiling. Choose one set of T-Rail mounting kits from the bundled package. Put the T-Rail brackets on the holes of the bottom side of the device. - Page 12 Attach the T-Rail brackets to the ceiling frame. Note Warning: The screw set shown below is for wall mounting only. Do not use such set for ceiling mounting due to the danger of falling.
-
Page 13: Wall-Mounted Installation
For wall-mounting, the VigorAP has keyhole type mounting slots on the underside. You can fit the AP at any axis (i.e. 12, 3, 6 or 9 O’Clock) to allow for cable entry from the most convenient location if you are using side entry – note the position of the side entry cable cutout. -
Page 14: Connection And Configuration
If required, remove the protective cap of VigorAP to create extra space for the cables to pass through. Connect VigorAP to Vigor router (via LAN port) with Ethernet cable. Connect VigorAP to PoE switch (via LAN port) with Ethernet cable. For connecting with PoE switch, do not connect the power adapter. -
Page 15: Connect To A Vigor Router Using Ap Management
Access into the web user interface of Vigor router. Here we take Vigor2862 as an example. Open Central Management>>AP>>Status. Locate VigorAP 960C. Click the IP address assigned by Vigor router to access into web user interface of VigorAP 960C. After typing username and password (admin/admin), the main screen will be... -
Page 16: Web Configurations
As a mesh node, settings related to VigorAP 960C must be configured by a remote Mesh Root (e.g., VigorAP 903) within the mesh network. The user must detect VigorAP 960C via a Mesh Root to add it as a mesh node. - Page 17 You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be in the same subnet as the IP address of VigorAP 960C. If there is no DHCP server on the network, then VigorAP ...
- Page 18 (c) Follow the on-screen steps to finish the network connection. Method 2: (a) Use a mobile phone to scan the QR code named with DrayTek Wireless App to download DrayTek Wireless APP. (b) After downloading, run the APP. (c) Click Quick Start Wizard. Next, scan the QR code named with Connect SSID.
-
Page 20: Customer Service
If the device cannot work correctly after trying many efforts, please contact your dealer/DrayTek for further help right away. For any questions, please feel free to send e-mail to “support@draytek.com”. Web registration is preferred. You can register your Vigor router via http://www.draytek.com.