Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Draytek VigorAP 912C
Summary of Contents for Draytek VigorAP 912C
-
Page 2: Quick Start Guide
We warrant to the original end user (purchaser) that the access point will be free from any defects in workmanship or materials for a period of two (2) years from the date of purchase from a DrayTek authorized dealer in the UK/Ireland. Please keep your purchase receipt in a safe place as it serves as proof of date of purchase. - Page 3 Importer: SEG, 11 Capital Business Park, Borehamwood, Hertfordshire WD6 1GW. The VigorAP 912C is designed for 2.4GHz and 5GHz WLAN network use in the UK & Ireland. Users in the UK & Ireland can sign up to our mailing list which goes...
-
Page 4: Declaration Of Conformity
Declaration of Conformity Hereby, DrayTek Corporation declares that the radio equipment type VigorAP 912C is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.draytek.com.tw/ftp/VigorAP 912C/Document/CE/ Manufacturer: DrayTek Corp. -
Page 5: Table Of Contents
4.3.1 Connected as a Mesh Node (in Mesh Network) ............9 4.3.2 Connected as an Access Point ................... 10 Method 1 – Web Interface ................... 11 Method 2 – DrayTek Wireless app ................15 Keep up to date with our mailing list ..............16 Firmware Updates ....................16... -
Page 6: Package Contents
You should only use the supplied power supply (as shown ⚫ above). If you have lost or damaged any components or accessories, obtain original DrayTek replacements only as they are safety approved/tested and should ensure that your unit operates correctly. Contents shown may vary. -
Page 7: Product Layout
Factory Ethernet Status Power Jack Reset Port (DC IN) Status Explanation Blue LED The VigorAP is starting up Blinking The VigorAP is ready and operating normally Green LED Blinking System is in Mesh mode or Range Extender mode and works normally Orange LED Blinking The VigorAP is in TFTP or Firmware Recovery mode... -
Page 8: Installation
Your VigorAP can be fitted to walls or ceilings and with the cable entry being from behind or from the side. Due to the optimized signal pattern, we do not recommend placing the VigorAP horizontally on a desk or shelf. Run your cables before you fit the VigorAP or bracket to the ceiling/wall. -
Page 9: Attaching Vigorap To The Ceiling Bracket
Install the supplied screws into the back of the AP. These special screws protrude from the back of the AP, leaving a bayonet type fitting to attach to the bracket: Lift the VigorAP up to the bracket and connect up the power and Ethernet cables. Line up the fixing screws and gently rotate the AP in order that the bayonets connect and ensure a comfortable fit into the slots. -
Page 10: Suspended Ceiling (Lightweight Steel Frame)
You cannot screw into ceiling tiles as they are weak and not suitable for bearing loads. Your VigorAP is supplied with mounts (T-Rail brackets) which attach directly to the metal grid (‘T-Rail’) of your suspended ceiling. Choose one set of T-Rail mounts to suit the size (gauge) of your T-rail. Fix the mounts into the underside of the VigorAP with the supplied screws: T-Rail Bracket... -
Page 11: Wall Mounting
Attach the T-Rail brackets to the ceiling frame: For wall-mounting, the VigorAP has keyhole type mounting slots on the underside. You can fit the AP at any axis (i.e. 12, 3, 6 or 9 O’Clock) to allow for cable entry from the most convenient location if you are using side entry –... -
Page 12: Connection And Configuration
⚫ If required, remove the protective cap of VigorAP to create extra space for the cables to pass through. ⚫ Connect VigorAP to Vigor router (via LAN port) with Ethernet cable. ⚫ Connect the VigorAP to PoE switch/injector (via LAN port) with Ethernet cable. -
Page 13: Connect To A Vigor Router Using Ap Management
This lists the VigorAP access points detected by the router’s Central AP Management: Locate VigorAP 912C. Click the IP address assigned by Vigor router to access into web user interface of VigorAP 912C. After typing username and password (admin/admin), the main screen will be... -
Page 14: Initial Configuration
Install the VigorAP on to the ceiling. As a mesh node, settings related to VigorAP 912C must be configured by a remote Mesh Root (e.g., VigorAP 903) within the mesh network: Method 1 - Mesh Root AP’s Web Interface: Access the web interface of the Mesh Root AP. -
Page 15: Connected As An Access Point
As an access point, the VigorAP 912C needs to be connected to a router and configured in AP (Access Point) / Range Extender mode. Install the VigorAP on to the ceiling. Use a twisted-pair cable with RJ-45 plugs at both ends, and plug into Ethernet device (e.g., Vigor router) and Ethernet port of VigorAP. -
Page 16: Method 1 - Web Interface
There are two methods to configure the VigorAP 912C: Method 1 – Web Interface (a) First, open a web browser on your PC and type https://192.168.1.2. A pop-up window will open to ask for username and password. Default Username... - Page 17 (c) Select an operation mode (Access Point, Mesh Root, Mesh Node or Range Extender) and click Next Step. This guide demonstrates the setup of Access Point (AP) mode: (d) Configure the VigorAP’s wireless network name and security settings (for both 2.4GHz and 5GHz). WiFi Name We recommend changing the default SSID (the wireless network name which is visible to...
- Page 18 WiFi Password The VigorAP has a default security key printed on a label on its base. You should change the password here – choose a ‘strong’ password (complex with a mix of letters, symbols and numbers). Enable 2 WiFi If you want to provide two networks (SSIDs) which clients can connect to then you can enable a 2 network name.
- Page 19 (f) Now, a summary of settings configuration will be shown on screen. Click Finish. The VigorAP will restart with the details specified in the Quick Start Wizard. The VigorAP will be ready for use once it has restarted.
-
Page 20: Method 2 - Draytek Wireless App
Method 2 – DrayTek Wireless app (a) Use a mobile phone to scan the QR code named with DrayTek Wireless App to download DrayTek Wireless APP. (b) After downloading, run the APP. (c) Click Quick Start Wizard. Next, scan the QR code named with Connect SSID. -
Page 21: Keep Up To Date With Our Mailing List
Now that you have your DrayTek product, you should keep up to date with product updates (firmware), security advisories and other product news, advice or special offers. Users in the UK/Ireland can subscribe to our mailing list. For details and to subscribe, please visit www.draytek.co.uk/list. - Page 22 GNU GENERAL PUBLIC LICENSE. The author of the software does not provide any warranty. A Limited Warranty is offered on DrayTek products. This Limited Warranty does not cover any software applications or programs. To download source codes please visit: http://gplsource.draytek.com...