Makita DUN500WRTE Instruction Manual page 6

Cordless pole hedge trimmer
Hide thumbs Also See for DUN500WRTE:
Table of Contents

Advertisement

Operation
1.
Always use two hands to operate the tool fitted
with two handles. Using one hand could cause
loss of control and result in serious personal injury.
2.
While operating the tool, always ensure that
the operating position is safe and secure.
Overreaching with the tool, particularly from
a ladder, is extremely dangerous. Do not work
from anything wobbly or infirm.
3.
Do not simultaneously wear multiple belt har-
nesses and/or shoulder harnesses when oper-
ating the tool.
4.
During operation, keep bystanders or animals
at least 15 m away from the tool. Stop the tool
as soon as someone approaches.
5.
If cutting tool strikes any object or the tool
starts making unusual noise or vibration,
switch off the tool and remove the battery car-
tridge immediately and allow the tool to stop.
And then take the following steps:
inspect for damage
check for, and tighten, any loose parts
have any damaged parts replaced or
repaired with genuine spare parts.
6.
Only use the tool for its intended purpose. Do
not use the tool for any other purpose.
7.
Switch off the tool and remove the battery
cartridge before:
cleaning or when clearing a blockage,
checking, carrying out maintenance or
working on the tool,
adjusting the working position of the
shear blades,
leaving the tool unattended.
8.
Ensure that the tool is correctly located in a
designated working position before starting
the tool.
9.
Do not operate the tool with a damaged or
excessively worn shear blades.
10. Always ensure that all handles and guards
are fitted when using the tool. Never attempt
to use an incomplete tool or one fitted with an
unauthorized modification.
Always be aware of your surroundings and
11.
stay alert for possible hazards of which you
may not be aware due to the noise of the tool.
12. Be careful not to accidentally contact a metal
fence or other hard objects during operation.
The blade will break and may cause serious injury.
13. Avoid unintentional starting. Do not carry the
tool when the battery cartridge is installed
and with finger on the switch. Make sure that
the switch is off when installing the battery
cartridge.
14. Do not grasp the exposed cutting blades or
cutting edges when picking up or holding the
tool.
15. Do not force the tool. It will do the job better and
with less likelihood of a risk of injury at the rate for
which it was designed.
16. Do not use the tool in the rain or in wet or
very damp conditions. The electric motor is not
waterproof.
17. Hold the tool firmly when using the tool.
18. Do not operate the tool at no-load
unnecessarily.
19. Before checking the shear blades, taking care
of faults, or removing foreign objects caught
in the shear blades, always switch off the tool
and remove the battery cartridge.
20. Never point the shear blades to yourself or
others.
21. If the blades stop moving due to the stuck of
foreign objects between the blades during
operation, switch off the tool and remove the
battery cartridge, and then remove the foreign
objects using tools such as pliers. Removing
the foreign objects by hand may cause an injury
for the reason that the blades may move in reac-
tion to removing the foreign objects.
Maintenance and storage
1.
When the tool is stopped for servicing, inspec-
tion or storage, switch off the tool and remove
the battery cartridge, and make sure all mov-
ing parts have come to a stop. Allow the tool
to cool before making any inspections, adjust-
ment, etc.
Always allow the tool to cool down before
2.
storing.
When not in use, attach the blade cover to the
3.
tool and store the tool indoors in dry, and high
locked-up place, out of reach of children.
4.
Maintain the tool with care. Keep cutting edge
sharp and clean for best performance and to
reduce the risk of injury. Follow instructions
for lubricating and changing accessories.
Keep handles dry, clean, and free from oil and
grease.
5.
Check damaged parts. Before further use of
the tool, any part which is damaged should be
carefully checked to determine that it will oper-
ate properly and perform its intended function.
Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting
and any other condition that may affect its
operation. A guard or other part that is damaged
should be properly repaired or replaced by your
authorized service center.
6.
Use genuine spare parts only.
When moving the tool to another location,
7.
including during work, always remove the
battery cartridge and put the blade cover on
the shear blades. Never carry or transport the
tool with the blades running. Never grasp the
blades with your hands.
8.
Clean the tool and especially the shear blades
after use, and before putting the tool into stor-
age for extended periods. Lightly oil the shear
blades and put on the blade cover.
9.
Do not dispose of the battery(ies) in a fire. The
cell may explode. Check with local codes for
possible special disposal instructions.
10. Do not open or mutilate the battery(ies).
Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be
toxic if swallowed.
6 ENGLISH

Advertisement

Table of Contents
loading

This manual is also suitable for:

Dun600lDun500wDun600lrte

Table of Contents