Makita DSC250 Instruction Manual
Cordless steel rod cutter
Hide thumbs
Also See for DSC250:
- Instruction manual (168 pages) ,
- Original instructions manual (44 pages) ,
- Instruction manual (168 pages)
Table of Contents
Related Manuals for Makita DSC250
Summary of Contents for Makita DSC250
- Page 1 INSTRUCTION MANUAL Cordless Steel Rod Cutter DSC250 Read before use. Before installing and operating this machine, read, understand and follow all instructions and operating procedures. Keep this Instruction Manual with the machine.
-
Page 2: Specifications
*** Makita shall not be responsible for any inci- Moving blade. Keep hands clear while machine is operating. Turn power off before servicing. dental damages or personal injuries result-... -
Page 3: Ec Declaration Of Conformity
• This manual should be retained for future described in this Instruction Manual and the reference. Makita catalog. Use of any other accessories or WARNING attachments may result in an accident or injury. 12. Do not expose the battery to fire as it may Before use, read this Instruction Manual explode or generate poisonous substances. - Page 4 Instruction Manual and the and do not allow persons unfamiliar with the power Makita catalog. Use of any other accessories or tool or these instructions to operate the power attachments may result in an accident or injury.
- Page 5 Do not use water or cutting oil when cutting. result in a hazardous situation. 12. Use only Makita genuine tipped saw. Battery tool use and care 13. Do not leave the tool on the floor with switch Recharge only with the charger specified by locked on.
- Page 6 WARNING: Use only Makita supplied Tipped a cap to be away from rotating blades. Saw. Using non Makita parts may damage the tool Before use and can result in serious accident or injury. Ensure that Tipped Saw Blades are not deformed, chipped, cracked or worn-out.
-
Page 7: Part Names
Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery burst- ing causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger. 7 ENGLISH... -
Page 8: Operating Procedure
Low battery voltage: The remaining battery capacity is too low and the tool will not operate. In this situation, remove and recharge the battery. OPERATING PROCEDURE WARNING: Before the battery is inserted into Fig.2 the tool, ensure that the Switch is at the “O” posi- tion and the Switch is off. -
Page 9: Operation
Position the Guide in the opening against the Operation rebar. Then push the tool forward slowly to start to cut the rebar. CAUTION: When cutting, both at the begin- ning and near the end, slow down the tool’s for- ward (cutting) movement. A fast cutting action, at these times, will damage the Tipped Saw blades and can cause injury from flying debris. - Page 10 The surface of the cut piece is discolored by heat. Table 1 NOTE: Tipped Saw blades cannot be resharpened. Battery indicator status Remaining battery capacity :Off :Blinking How to fit the Dust Bag 5 0 %-1 0 0 % 2 0 %-5 0 % 0 %-2 0 % Charge the battery Automatic speed change function Fig.7...
- Page 11 Remove the Tipped Saw Guide and the Tipped Saw. How to replace the Tipped Saw CAUTION: Use only Makita supplied Tipped Saw. If reusing a Tipped Saw, ensure it is not worn, chipped or damaged. CAUTION: Clean and remove all debris and dirt from the Tipped Saw and parts.
-
Page 12: Maintenance
Replace the Tipped Saw CAUTION: Clean the Dust Cover when it becomes clogged. Continuing operation with a clogged dust cover may damage the tool. Fig.12 ► Fig.12: 1. Push (Lock Button) Fit the Tipped Saw over the Output Gear, making sure that the slot in the flange is properly aligned with the key. - Page 13 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan DSC250-ENEU-1610 www.makita.com 20161019...