Maintenance; Optional Accessories - Makita GF600 Instruction Manual

Dry fire prevention automatically functions when the rest
of nails get to the last 9-11 pieces.
Jammed nailer
WARNING:
• Always be sure to remove the fuel cell and the battery
cartridge before clearing a jam.
CAUTION:
• Do not use deformed nails or nail strip. Failure to do so
causes poor nail feeding.
Follow the removing nail procedure and remove the nails
in the magazine. (Fig. 24)
Open the latch and release the door, then remove the
jammed nail.

MAINTENANCE

CAUTION:
• Always remove the fuel cell, the battery cartridge and
nails before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Maintenance after daily work
At the end of daily work, conduct an end-of-workday
routine.
These simple steps are based on maintaining the safety
and performance of the tool.
Before leaving the work site:
• Remove the battery cartridge and store in a tool-
carrying case. Always use the tool-carrying case for
transporting and storing the tool.
• Dispose of all empty cells where they will not be found
by children, crushed, punctured or burned.
When you get home:
• Place the battery cartridge in its charger if it needs
charging as indicated by the red indication lamp.
• Wipe the tool with a clean, soft cloth.
• Check the filter and clean if it is dusty.
Cleaning the air filter (Fig. 25 & 26)
Press slightly up the filter cover and remove it. And then
simply lift out the filter.
Tap the filter lightly to remove any dust. Soap and water
restores the filter to an almost new condition
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
Thoroughly cleaning
If dry fires occur frequently, which means the tool is
needed to be cleansed thoroughly.
See the accompanying cleaning guide for detail, and
perform the cleaning.
If you have any questions regarding to cleaning, please
ask your local Makita Service Center.
10

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Nails
• Safety goggles
• Fuel cell
• Cleaning kit
• Makita genuine battery and charger
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
Noise
The typical A-weighted noise level determined according
to EN792:
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Wear ear protection
Vibration
The vibration total value determined according to EN792:
Vibration emission (a
Uncertainty (K): 1.5 m/s
• The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to
the trigger time).
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Cordless Brad Nailer
Model No./Type: GF600
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN792, EN60745
ENG905-1
): 93 dB (A)
pA
): 106 dB (A)
WA
ENG904-2
2
): 3.5 m/s
h
2
ENG901-1
ENH003-13