Makita DGA452Z Instruction Manual
Cordless angle grinder
Hide thumbs
Also See for DGA452Z:
- Instruction manual (152 pages) ,
- Instruction manual (104 pages) ,
- Instruction manual (76 pages)
Related Manuals for Makita DGA452Z
Summary of Contents for Makita DGA452Z
- Page 1 INSTRUCTION MANUAL Cordless Angle Grinder DGA402 DGA450 DGA452 007214 IMPORTANT: Read Before Using.
-
Page 2: Specifications
ENGLISH (Original instructions) SPECIFICATIONS Model DGA402 DGA450 DGA452 Wheel diameter 100 mm 115 mm Max. wheel thickness 6.4 mm 6.4 mm 6.4 mm Spindle thread M14 or 5/8" (country specific) Rated speed (n) / No load speed (n 11,000 (min Overall length 317 mm Net weight... -
Page 3: Ec Declaration Of Conformity
EC Declaration of Conformity Electrical safety Power tool plugs must match the outlet. Never Makita declares that the following Machine(s): modify the plug in any way. Do not use any Designation of Machine: adapter plugs with earthed (grounded) power Cordless Angle Grinder tools. - Page 4 the influence of drugs, alcohol or medication. A 22. Keep cutting tools sharp and clean. Properly moment of inattention while operating power tools maintained cutting tools with sharp cutting edges may result in serious personal injury. are less likely to bind and are easier to control. Use personal protective equipment.
- Page 5 personal injury. wiring. Contact with a "live" wire will also make Do not use accessories which are not exposed metal parts of the power tool "live" and specifically designed and recommended by could give the operator an electric shock. the tool manufacturer. Just because the Never lay the power tool down until the accessory can be attached to your power tool, it accessory has come to a complete stop.
- Page 6 have a tendency to snag the rotating accessory wheel comes to a complete stop. Never attempt and cause loss of control or kickback. to remove the cut-off wheel from the cut while e) Do not attach a saw chain woodcarving the wheel is in motion otherwise kickback may blade or toothed saw blade.
- Page 7 wobbling that could indicate poor installation Do not disassemble battery cartridge. or a poorly balanced wheel. If operating time has become excessively 21. Use the specified surface of the wheel to shorter, stop operating immediately. It may perform the grinding. result in a risk of overheating, possible burns 22.
-
Page 8: Functional Description
In this situation, turn the tool off and stop the FUNCTIONAL DESCRIPTION application that caused the tool to become overloaded. Then turn the tool on to restart. If the tool does not start, the battery is CAUTION: overheated. In this situation, let the battery Always be sure that the tool is switched off and the •... -
Page 9: Shaft Lock
Battery cartridge replacing signal ASSEMBLY When the remaining battery capacity is low, the indicator lamp lights up during operation earlier than that of high battery capacity. CAUTION: Accidental re-start preventive function Always be sure that the tool is switched off and the •... -
Page 10: Operation
remove wheel guard, follow installation OPERATION procedure in reverse. Installing or removing depressed center WARNING: grinding wheel/Multi-disc It should never be necessary to force the tool. The • weight of the tool applies adequate pressure. 1. Lock nut Forcing and excessive pressure could cause 2. - Page 11 Operation with abrasive cut-off / diamond wheel (optional accessory) 1. Lock nut 2. Abrasive cut-off wheel/diamond wheel 3. Inner flange 4. Wheel guard for abrasive cut-off wheel/diamond wheel 010855 The direction for mounting the lock nut and the inner flange varies by wheel thickness. Refer to the table below.
-
Page 12: Maintenance
Reinstall the holder cap cover on the tool. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, 007222 always using Makita replacement parts. The tool and its air vents have to be kept clean. -
Page 13: Optional Accessories
Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. Wheel guard (Wheel cover) for depressed center • wheel / multi disc Wheel guard (Wheel cover) for abrasive cut-off •... - Page 16 Makita Jan-Baptist Vinkstraat 2, 3070, Belgium Makita Corporation Anjo, Aichi, Japan www.makita.com 885268B223...