16. Screw 25. Carbon brush cap Speed change lever 17. Bit holder 26. Hole Action mode changing ring 18. Bit SPECIFICATIONS Model DHP446 DHP456 Concrete 13 mm Steel 13 mm Capacities Wood 38 mm Wood screw 6 mm x 75 mm...
9. Do not touch the bit or the workpiece immediately 2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. after operation; they may be extremely hot and 3. Charge the battery cartridge with room could burn your skin. temperature at 10°C - 40°C (50°F - 104°F).
The remaining battery capacity is too low and the tool For rotation only, turn the ring so that the arrow on the tool will not operate. In this situation, remove and body points toward the mark on the ring. recharge the battery. For rotation with hammering, turn the ring so that the arrow points toward the mark on the ring.
Drilling operation Hold the tool firmly with one hand on the grip and the other hand on the bottom of the battery cartridge to First, turn the adjusting ring so that the pointer points to control the twisting action. marking. Then proceed as follows. CAUTION: Hammer drilling operation •...
• These accessories or attachments are recommended WARNING: for use with your Makita tool specified in this manual. • The vibration emission during actual use of the power The use of any other accessories or attachments might tool can differ from the declared emission value present a risk of injury to persons.
Omkeerschakelaar 16. Schroef 25. Koolborstelkap Snelheidsinstelknop 17. Bithouder 26. Opening Werkingsfunctie-keuzering 18. Bit TECHNISCHE GEGEVENS Model DHP446 DHP456 Beton 13 mm Staal 13 mm Maximale schroefmaat Hout 38 mm Houtschroef 6 mm x 75 mm 10 mm x 89 mm...
wanneer u werkt op plaatsen waar het Bewaar de accu niet op een plaats waar deze bevestigingsmateriaal met verborgen bedrading in in aanraking kan komen met andere metalen aanraking kan komen. Wanneer voorwerpen, zoals spijkers, munten, enz. bevestigingsmaterialen in aanraking komen met onder Stel de accu niet bloot aan water of regen.
Page 12
klikgeluid hoort. Als u het rode deel aan de bovenkant van OPMERKING: de knop kunt zien, is de accu niet goed aangebracht. • Gebruik een doek om het vuil van de lens van de lamp te vegen. Wees voorzichtig de lens van de lamp niet te LET OP: bekrassen om de lichtopbrengst niet te verlagen.
Het draaikoppel instellen (zie afb. 7) Gebruik als boorhamer Het draaikoppel kan in 16 stappen worden ingesteld door LET OP: de instelring te draaien zodat de gewenste stand op de • Op het moment dat het boorgat doorbreekt, het schaalverdeling is uitgelijnd met de pijlpunt op de boorgat verstopt raakt met schilfertjes of behuizing van het gereedschap.
Het gereedschap kan echter plotseling • Deze accessoires of hulpstukken worden aanbevolen achteruit komen als u het niet stevig vasthoudt. voor gebruik met het Makita-gereedschap dat in deze • Zet kleine werkstukken altijd vast in een bankschroef of gebruiksaanwijzing wordt beschreven. Het gebruik van klem ze in een soortgelijk bevestigingsmiddel.
Page 15
Het technische bestand volgens 2006/42/EG is Geluidsdrukniveau (L ): 80 dB (A) verkrijgbaar bij: Onzekerheid (K): 3 dB (A) Makita, Jan-Baptist Vinkstraat 2, 3070, België Het geluidsniveau kan tijdens gebruik hoger worden dan 80 dB (A). 31. 12. 2013 Model DHP456...