HIKVISION DS-2AE7232TI-A Quick Start Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. DS-2AE7232TI-A
  6. Quick start manual

HIKVISION DS-2AE7232TI-A Quick Start Manual

Hd-tvi speed dome
Hide thumbs Also See for DS-2AE7232TI-A:
Table of Contents

Advertisement

Quick Links

Download this manual
HD-TVI Speed Dome
Quick Start Guide
UD02198B

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION DS-2AE7232TI-A

Summary of Contents for HIKVISION DS-2AE7232TI-A

  • Page 1 HD-TVI Speed Dome Quick Start Guide UD02198B...
  • Page 2 SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
  • Page 3 HD-TVI Speed Dome·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. 03261060707...
  • Page 4 HD-TVI Speed Dome·Quick Start Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 5 HD-TVI Speed Dome·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
  • Page 6 HD-TVI Speed Dome·Quick Start Guide  Do not aim the speed dome at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.

  • Page 7: Table Of Contents

    HD-TVI Speed Dome·Quick Start Guide Table of Contents 1 Installation ......................1 1.1 Connecting the Cables ......................1 1.2 DIP Switch Settings ........................2 1.2.1 5-inch Speed Dome Settings ....................2 1.2.2 5-inch IR & Mini IR Speed Dome Settings ................4 1.2.3 7-inch IR Speed Dome Settings ..................

  • Page 8: Installation

    HD-TVI Speed Dome·Quick Start Guide 1 Installation Before you start: Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. There are several ways to install the analog speed dome. The wall mounting is taken as an example below.

  • Page 9: Dip Switch Settings

    HD-TVI Speed Dome·Quick Start Guide 1.2 DIP Switch Settings 1.2.1 5-inch Speed Dome Settings The DIP switch is used for setting the address and baudrate for the speed dome, with value ON=1 and OFF=0. The SW1 switches from the first to the eighth are used to set the address. The SW2 switches are used to set the baudrate.
  • Page 10 HD-TVI Speed Dome·Quick Start Guide Switch No. Dome Address … … … … … …  Protocol Settings The number 6 and 7 of SW1 switches are for setting the protocol of the speed dome. You can refer to Table 1-3 for details of setting the speed dome protocol. Table 1-3 Set the Protocol of the Dome Switch No.

  • Page 11: 5-Inch Ir & Mini Ir Speed Dome Settings

    HD-TVI Speed Dome·Quick Start Guide Table 1-5 Set the Baudrate of the Dome Switch No. Baudrate 2400 4800 9600 19200 1.2.2 5-inch IR & Mini IR Speed Dome Settings The DIP switch is for setting the speed dome address, baudrate, protocol, etc., with value ON=1 and OFF=0.
  • Page 12 HD-TVI Speed Dome·Quick Start Guide Figure 1-7 Enlarged View of DIP Switch  For some certain models, the two individual DIP switches at the left side of the Figure 1-7 are supported for turning on/off the terminator; while other models are not supported. ...
  • Page 13 HD-TVI Speed Dome·Quick Start Guide  Baudrate List For convenient settings, refer to the following list to set the baudrate for the speed dome. The baudrate will be set as 2400bps by default if it is out of this range. Table 1-8 Baudrate Switch Baudrate...

  • Page 14: 7-Inch Ir Speed Dome Settings

    HD-TVI Speed Dome·Quick Start Guide 1.2.3 7-inch IR Speed Dome Settings Two DIP switches SW1 and SW2 are for setting the speed dome address, baudrate, protocol, etc., with value ON=1 and OFF=0. The switch label is on the back of the SWITCH cover as shown in Figure 1-8.
  • Page 15 Table 1-14 Set the Protocol of the Dome DIP Switch SW2-Protocol Settings Protocol Self-adaptive PELCO_P PELCO_D HIKVISION KALATE VICON MAN_BOSCH MAN_AD  TVI Mode Settings The No. 7 of SW2 switches is for setting the TVI mode of the speed dome. You can refer to the following table for details of setting the speed dome TVI mode.

  • Page 16: Mini Speed Dome Settings

    HD-TVI Speed Dome·Quick Start Guide  Terminal Resistor Settings The No. 8 of SW2 switches is used for turning on/off the 120Ω terminal resistor. Table 1-16 Set Terminal Resistor Terminal Matching Resistance Turn on the Resistor Turn off the Resistor The o-ring in the groove of the switch cover is for waterproof.
  • Page 17 HD-TVI Speed Dome·Quick Start Guide The DIP switch is designed according to binary system. When the switch is ON, it stands for the number 1. When the switch is OFF, it stands for the number 0. Example: The SW1 switches from No. 1 to 5 are used to set the speed dome address. No. 1 is the lowest digit and No.

  • Page 18: Wiring And Installation

    HD-TVI Speed Dome·Quick Start Guide Table 1-20 Protocol Switch No. Protocol Self-adaptive Pelco_P The speed dome is self-adaptive to private protocol when the No.8 and 9 switches are both OFF.  TVI Mode For convenient settings, refer to the following list to set the TVI mode of the speed dome. Table 1-21 TVI Mode Switch No.

  • Page 19: Installing The Bracket

    HD-TVI Speed Dome·Quick Start Guide  To protect the power cable and the signal transmitting cable from human tampering, you should pay attention to the protection and reinforcement of the cables.  When deploying the wire, please do not tighten the wire or make the wire loose. The wiring of the speed dome should be performed by professionals.

  • Page 20: Setting The Dip Switch

    HD-TVI Speed Dome·Quick Start Guide Figure 1-14 Secure the Mount 5. Install the speed dome to the mount. Please refer to Section 1.3.4 Installing the Speed Dome for installation details. Follow the same instructions described above for the short-arm wall mounting. For outdoor applications, please adopt the water-proof measures.

  • Page 21: In-Door Mounting Applications

    HD-TVI Speed Dome·Quick Start Guide 2 In-door Mounting Applications Before you start:  For cement wall, you need to use the expansion screw to fix the mount. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the mount. ...
  • Page 22 HD-TVI Speed Dome·Quick Start Guide Figure 2-2 Draw and Cut Hole on the Ceiling 6. Connect the cables. Make sure the video cable and control wire have been connected to the corresponding interfaces. Connect the power cable and the red LED indicator turns on when the power is on. Please turn the power off after checking the speed dome.

  • Page 23: 5-Inch Speed Dome Ceiling Mounting Applications

    HD-TVI Speed Dome·Quick Start Guide 8. Install the trim ring. (1) Attach the trim ring to the lower dome and align the triangular notch of the trim ring with the arrow label on the in-ceiling mount. (2) After having firmly placed the trim ring to the ceiling, rotate the trim ring in the direction of arrow to secure the trim ring in place.

  • Page 24: Wiring

    HD-TVI Speed Dome·Quick Start Guide Figure 2-6 Remove 4 screws 2. Remove the in-ceiling mounting bracket. Figure 2-7 Remove the in-ceiling mounting bracket 3. Screw 4 bolts onto the back box by a Phillips screwdriver. Figure 2-8 Install the bolts 2.2.2 Wiring The cables of dome can be routed either from the top or the side of the back box.

  • Page 25: Ceiling Mounting

    HD-TVI Speed Dome·Quick Start Guide Figure 2-9 Cabling for Ceiling Mounting 2.2.3 Ceiling Mounting Steps: 1. Rotate the lower dome counterclockwise to separate it from the back box. Refer to the Figure 2-1. 2. Remove the protective lens cover, foam and sticker from the dome drive. Set the address and baudrate for the analog speed dome.
  • Page 26 HD-TVI Speed Dome·Quick Start Guide Screw Holes Cable Hole Figure 2-11 Secure the Mounting Base 8. Install the speed dome to the mounting base. (1) Route the cables for the speed dome. Align the bottom of the speed dome with the mounting base.

  • Page 27: Mini Speed Dome In-Ceiling Mounting Applications

    HD-TVI Speed Dome·Quick Start Guide 2.3 Mini Speed Dome In-ceiling Mounting Applications Before you start: The in-ceiling mounting is applicable to the indoor ceiling construction. The followings are the mandatory precondition for mounting:  The height of the space above the ceiling must be more than 250mm. ...
  • Page 28 HD-TVI Speed Dome·Quick Start Guide Rotate the bolts through the screw holes. Reinstall the toggles as shown in Figure 2-15. Toggle Bolt Figure 2-15 Install the Toggle Bolts 4. Align the toggle bolts with the screw holes on the ceiling. 5.

  • Page 29: Mini Speed Dome Ceiling Mounting Applications

    HD-TVI Speed Dome·Quick Start Guide 2.4 Mini Speed Dome Ceiling Mounting Applications Before you start: The ceiling mounting is applicable to the indoor/outdoor solid ceiling construction. The followings are the mandatory precondition for ceiling mounting:  The ceiling must be with the thickness between 5 and 40mm. ...
  • Page 30 HD-TVI Speed Dome·Quick Start Guide Protective Foam Notch Lower Dome Lens Cover Sticker Figure 2-20 Disassemble the Speed Dome 3. Attach lower dome to the back box, and secure it with screws. 4. Align the ceiling mount with the screw holes on the drill template. Secure the ceiling mount to the ceiling with screws (supplied).

  • Page 31: Application And Operations

    HD-TVI Speed Dome·Quick Start Guide 3 Application and Operations 3.1 System Application The device can be controlled through the back-end device or control software. The back-end device includes control keyboard, DVR (Digital Video Recorder), etc., and the control software includes client software.

  • Page 32: Configuring Patrol

    HD-TVI Speed Dome·Quick Start Guide MAIN MENUS <SYSTEM INFO> <DOME SETTINGS> <RESTORE SETTINGS> <RESTORE CAMERA> <REBOOT DOME> <LANGUAGE> ENGLISH EXIT Figure 3-2 Main Menu Refer to the user manual for the detailed instruction to set the speed dome. 3.2.1 Configuring Patrol You can set the patrol function by the DVR and OSD menu, as well as the one-touch patrol can be realized.
  • Page 33 HD-TVI Speed Dome·Quick Start Guide Figure 3-4 Key point Configuration 4. Configure key point parameters, such as the key point No., duration of staying for one key point and speed of patrol. The key point is corresponding to the preset. The Key Point No. determines the order at which the PTZ will follow while cycling through the patrol.
  • Page 34 HD-TVI Speed Dome·Quick Start Guide Up to 8 patrols can be configured. 3. Edit the patrol. Move the cursor to EDIT PATROL and click IRIS+ to enter edit mode. NUM PST DWELL SPEED IRIS+ OK IRIS- CANCEL Figure 3-6 Edit the Patrol Click up/down direction buttons to choose the number and locate the preset to be edited.

  • Page 35: Configuring Park Actions

    HD-TVI Speed Dome·Quick Start Guide 3.2.2 Configuring Park Actions Purpose: For some certain model of the speed dome, it can be configured to start a predefined park action (scan, preset, patrol and etc.) automatically after a period of inactivity (park time). ...
  • Page 36 HD-TVI Speed Dome·Quick Start Guide MOTION AUTO FLIP PROPORTIONAL PAN PARK TIME PARK ACT NONE SCAN SPEED IMAGE FREEZE DOME SPEED BACK EXIT Figure 3-8 PTZ Configuration 2. Move the cursor to the PARK TIME, and set the value in the range from 5 to 720 seconds. 3.

  • Page 37: Troubleshooting

    HD-TVI Speed Dome·Quick Start Guide 4 Troubleshooting 4.1 Device Exceptions Question Why does the speed dome fail to start or repeatedly reboot? Why does the speed dome restart intermittently when controlling PTZ, calling presets or turning on the infrared lights of the IR dome at night? Answer ...
  • Page 38 HD-TVI Speed Dome·Quick Start Guide Answer  Please check whether the protective film of the bubble has been removed.  Please check whether there are foreign objects on the bubble or the lens.  Please check where there are obstructions such as spider web nearby. ...
  • Page 39 HD-TVI Speed Dome·Quick Start Guide...

Table of Contents