Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-2AE5232TI-A
Summary of Contents for HIKVISION DS-2AE5232TI-A
- Page 1 HD-TVI Speed Dome User Manual UD.6L0201D1620A02...
- Page 2 User Manual of HD-TVI Speed Dome Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact the dealer. This manual is applicable to HD-TVI Speed Domes. This manual may contain several technically inaccurate points or printing errors, and the content is subject to change without notice.
- Page 3 User Manual of HD-TVI Speed Dome Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 4 User Manual of HD-TVI Speed Dome Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precaution measure is divided into ‘Warnings’ and ‘Cautions’: Warnings: Serious injury or death may be caused if any of these warnings are neglected. Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
- Page 5 User Manual of HD-TVI Speed Dome Cautions: Make sure the power supply voltage is correct before using the product. Do not drop the product or subject it to physical shock. Do not install the product on vibratory surface or places. ...
-
Page 6: Table Of Contents
User Manual of HD-TVI Speed Dome Table of Contents Chapter 1 Overview .............................. 6 Description ................................6 Functions ................................6 Chapter 2 Getting Started ............................. 9 Power-up Action ..............................9 Basic Operations ..............................10 System-defined Presets ............................10 On-screen Displays ............................. 11 Chapter 3 Menu Operation .......................... -
Page 7: Chapter 1 Overview
User Manual of HD-TVI Speed Dome Chapter 1 Overview 1.1 Description Integrated with the built-in pan/tilt unit, the E series speed dome features highly sensitive response and reliable performance. The speed dome can be adopted in various surveillance fields with its full-integral functions and features, such as corridor, large venue, meeting room, station, neighborhoods, etc. - Page 8 User Manual of HD-TVI Speed Dome In manual tracking mode, when a target object goes directly beneath the dome, the video will automatically flips 180 degrees in horizontal direction to maintain continuity of tracking. This function can also be realized by auto mirror image depending on different camera models. ...
- Page 9 User Manual of HD-TVI Speed Dome are in auto status during the pattern is being memorized. Power Off Memory The dome supports the power off memory capability with the predefined resume time. It allows the dome to resume its previous position after power is restored. ...
-
Page 10: Chapter 2 Getting Started
User Manual of HD-TVI Speed Dome Chapter 2 Getting Started 2.1 Power-up Action After the speed dome is power-on, it will perform a series of self-test actions. It runs the pan checking firstly, then the tilt checking and the camera checking at last. After the power-up actions, the system information will be displayed for 2 minutes on the live view screen as shown below. -
Page 11: Basic Operations
User Manual of HD-TVI Speed Dome 2.2 Basic Operations You can operate the speed dome using a control device, including the control keyboard, DVR, DVS, etc. In this manual, accessing the speed dome via the web browser will be taken as an example. Panning and tilting: Click the direction buttons to control the pan and tilt movement of the speed dome. -
Page 12: On-Screen Displays
User Manual of HD-TVI Speed Dome 2.4 On-screen Displays The speed dome supports following on-screen displays: Zoom Show: Identifies the amount of magnification. The format is ZXXX. XXX is the zoom amount. PT Show: Displays panning and tilting direction, with the format of NEXXX/TXXX. The NE followed with XXX indicates the degrees in north east direction, while the T followed with XXX indicates the degrees in tilt position. -
Page 13: Chapter 3 Menu Operation
User Manual of HD-TVI Speed Dome Chapter 3 Menu Operation The operation interface of the different speed domes may differ. Please refer to the actual operation interface. You can click the left and right direction buttons in the PTZ control panel via the web browser of the DVR to enter the next page or return to the previous page of the submenu if more than one page is available. -
Page 14: Accessing And Operating The Menu
User Manual of HD-TVI Speed Dome 3.1 Accessing and Operating the Menu To enter the main menu: Steps: 1. Connect the video and RS-485 cables of speed dome to a DVR. 2. Visit the DVR via the web browser. 3. View the live video of the speed dome. 4. -
Page 15: Configuring System Parameters
User Manual of HD-TVI Speed Dome System information menu displays the current system information of the speed dome, including model, address, protocol, etc. The information shown on this submenu is similar to the system information shown after the power-up action. Please refer to Section 2.1 for more details. Enter the system information display menu: MAIN MENUS >... - Page 16 User Manual of HD-TVI Speed Dome Dome address settings To Set the Soft Address of the Speed Dome If the SET SOFT ADDR is set as ON, the soft address is the valid address for connecting the speed dome. The selectable soft address range is from 1 to 255; If the SET SOFT ADDR is set as OFF, the hard address set by the DIP switch is the valid address of the speed dome.
- Page 17 User Manual of HD-TVI Speed Dome Y - M - D 12 12 12 H - M - S 15 33 25 IRIS + OK IRIS - CANCEL Figure 3-5 Set the System Time Angle Zero Configuration Purpose: You can define the angle zero of the speed dome on the ANGLE ZERO submenu. Steps: (1) Move the cursor to ANGLE ZERO using the direction buttons and click IRIS+ to enter.
- Page 18 Select the protocol. Choose the protocol on PROTOCAL submenu. You can configure it as AUTO MATCH, PELCO-P, PELCO-D, or HIKVISION. When you choose AUTO MATCH, it is protocol self-adaptive. Set the protocol status. Set the PROTOCOL STATUS as ON to enable the user-defined protocol.
-
Page 19: Configuring Image Parameters
User Manual of HD-TVI Speed Dome You can set 485 CHECK as ON or AUTO for automatic RS-485 configuration diagnosis. If the configuration is incorrect, an alert will be received; if you set the value as AUTO, it will automatically stop the diagnosis when no errors exist. ... - Page 20 User Manual of HD-TVI Speed Dome CAMERA CAMERA CAMERA WB MODE AUTO MIN. ZOOM LIMIT GAIN LIMIT CHROMA SUPPRESS DEFOG BLUE SATURATION INIT LENS IMAGE FLIP CONTRAST FOCUS LIMIT SCENE MODE INDOOR 2D DNR 3D DNR SHARPNESS COMP BACK EXIT BACK EXIT BACK...
- Page 21 User Manual of HD-TVI Speed Dome If you set the ZOOM LIMIT as the minimum value 22, the digital zoom function will be disabled, and the optical zoom function is at its maximum value. Configure the zoom speed. Purpose: You can define the speed at which the lens changes from full wide zoom to the optical zoom.
- Page 22 User Manual of HD-TVI Speed Dome don’t support user-defined BLC level. Task 6: Configuring the iris, gain and shutter speed Set the Exposure Mode Purpose: AE mode defines the priority of iris, shutter and gain while the speed dome adjusting the brightness of the live view.
- Page 23 User Manual of HD-TVI Speed Dome The value of X indicates that the shutter speed is 1/X second. If you set the SHUTTER value bigger (shutter speed is faster), the amount of entering light per second is fewer, and the image is darker. (2) Slow shutter.
-
Page 24: Configuring Privacy Mask
User Manual of HD-TVI Speed Dome Task 12: Configure the image quality. Min. Zoom Limit Set the value of MIN. ZOOM LIMIT to ON to limit the minimum zoom of the lens. The Min. Zoom Limit function is supported by certain speed dome model series. ... - Page 25 User Manual of HD-TVI Speed Dome the size as the lens zooming in/out. Steps: 1. Move the cursor to enter the privacy mask configuration submenu: MAIN MENUS > DOME SETTINGS > PRIVACY MASK PRIVACY MASK MASK NO. MASK STATUS SET MASK DELETE MASK BACK EXIT...
-
Page 26: Configuring Output Standard
User Manual of HD-TVI Speed Dome up/down buttons to increase/decrease the height of the mask and click right/left buttons to increase/decrease the width of the mask. Click IRIS+ button to save the settings and return to the previous menu and you can see the mask turn to gray. (4) To modify the configured mask, click IRIS+ button to enter the SET MASK menu and click IRIS+ button again to edit. -
Page 27: Configuring Ptz Control Parameters
User Manual of HD-TVI Speed Dome IR SETTINGS SENSITIVITY MEDIUM N/M LED CURRENT FAR LED CURRENT ZOOM LIMIT IR CONTROL AUTO SWITCH DELAY(S) BACK EXIT Figure 3-10 IR Settings Set the sensitivity of the IR LED. You can set the SENSITIVITY to HIGH, MEDIUM, or LOW. ... - Page 28 User Manual of HD-TVI Speed Dome MAIN MENU > DOME SETTINGS > MOTION SETTINGS MOTION MOTION PRESET SPEED AUTO FLIP ENABLE LIMIT PROPORTIONAL PAN LIMITS SETTING PARK TIME CLEAR LIMITS PARK ACT NONE SET ELEVATION SCAN SPEED IMAGE FREEZING DOME SPEED BACK EXIT BACK...
- Page 29 User Manual of HD-TVI Speed Dome This feature enables the live view to switch directly from the current scene to another scene that is defined by a preset, without showing the middle areas between these two scenes. It reduces the use of bandwidth in a digital network system and it also provides privacy protection for the middle areas.
-
Page 30: Configuring Presets
User Manual of HD-TVI Speed Dome 3.4.2 Configuring Presets Purpose: A preset is a user-defined monitoring position/point. You can simply call the preset number to change the monitor scene to the defined position. Steps: 1. Move the cursor to enter preset configuration submenu: MAIN MENU >... -
Page 31: Configuring Patrols
User Manual of HD-TVI Speed Dome 3.4.3 Configuring Patrols Purpose: A patrol is a scanning track specified by a group of user-defined presets. You can call a patrol to scan the scenes automatically among the user-defined presets in sequence. Steps: 1. -
Page 32: Configuring Patterns
User Manual of HD-TVI Speed Dome (2) Click up/down direction buttons to choose the number and locate the preset to be edited. (3) Click left/right direction buttons to position the cursor to the column of PRESET, DWELL and SPEED. You can click the up/down direction buttons to set the value of preset number, dwell time and patrol speed. - Page 33 User Manual of HD-TVI Speed Dome PATTERNS PATTERN NO. RECORD PATTERN PREVIEW CLEAR REMAINING BACK EXIT Figure 3-15 Pattern Configuration Menu 2. Choose the pattern number. Steps: (1) Move the cursor to PATTERN NO. and click IRIS+ to enter edit mode. (2) Click the up/down direction buttons to select the number of the pattern which is to be configured.
-
Page 34: Configuring Timing Tasks
User Manual of HD-TVI Speed Dome remaining memory shown under PATTERNS menu as REMAINING. The pan/tilt movements and the lens operations cannot be memorized simultaneously. 4. Preview the pattern. Enter the PREVIEW menu to preview the current pattern. 5. Call the defined pattern. You can call the special presets to call the defined pattern. - Page 35 User Manual of HD-TVI Speed Dome Up to 8 time tasks can be configured. 3. Set the task status. Steps: (1) Move the cursor to ENABLE TASK and click IRIS+ to enter edit mode. (2) Click the up/down direction buttons to set the task status to ON. (3) Click IRIS+ again to confirm the settings and exit edit mode of this column.
-
Page 36: Configuring Zone
User Manual of HD-TVI Speed Dome 3.4.6 Configuring Zone Purpose: A zone is a panning and tilting area defined by the left/right limits. You can configure the zones on ZONES submenu. You can define a zone when the targeted surveillance scene is limited. Steps: 1. -
Page 37: Configuring And Handling Alarms
User Manual of HD-TVI Speed Dome Move the cursor to CLEAR ZONE, click IRIS+ to clear all the settings of the current zone, and click IRIS+ again to confirm the settings and exit. 3.5 Configuring and Handling Alarms The alarm related function is supported by the 5-inch IR speed dome only. 3.5.1 Configuring Alarm Input and Linkage Actions Purpose: This section explains how to configure the speed dome to respond to alarm events with alarm... -
Page 38: Configuring Alarm Parameters
User Manual of HD-TVI Speed Dome (3) Click IRIS+ again to confirm. If you set the status as OPEN, alarm will be triggered by high electricity level; if you set the status as CLOSE, alarm will be triggered by low electricity level; if you set the status as OFF, it will be triggered when this input channel is shut off. -
Page 39: Configuring Alarm Output
User Manual of HD-TVI Speed Dome position and resume from this position after the linkage action finishes. The speed dome can be configured to resume the PTZ positions, focus and iris value. 3.5.3 Configuring Alarm Output Purpose: An alarm output is a configurable alarm output interface on the speed dome back box which can connect and trigger another alarm device to operate. -
Page 40: Others
User Manual of HD-TVI Speed Dome 3.6 Others 3.6.1 Restoring Default Dome Settings Purpose: You can reset all dome settings to factory default parameters as shown in the table below. Dome settings are mainly of PTZ parameters and alarm parameters, and also include some system settings, e.g. -
Page 41: Appendix
User Manual of HD-TVI Speed Dome Appendix Appendix 1 Lightning & Surge Protection This product adopts TVS plate lightning protection technology to avoid damage caused by pulse signal that is below 3000W, like instantaneous lighting stroke, surging, etc. According to the actual outdoor situation, necessary protection measures must be taken, besides ensuring the electrical safety. -
Page 42: Appendix 2 Rs485 Bus Connection
User Manual of HD-TVI Speed Dome Appendix 2 RS485 Bus Connection General Property of RS485 Bus According to RS485 industry bus standard, RS485 is a half-duplex communication bus which has 120Ω characteristic impendence, the maximum load ability is 32 payloads (including controller device and controlled device). - Page 43 User Manual of HD-TVI Speed Dome Controller Figure A-4 Star Shape Connection For such case, the best way is adding a RS485 distributor. This product can effectively change the star-shape connection to which satisfies the requirement of RS485 industry standard, in order to avoid those problems and improve the communication reliability.
- Page 44 User Manual of HD-TVI Speed Dome Problem Possible Reasons To Solve the Problem 2. RS485+ or RS485-wire is 2. Change a RS485 wire. controlled broken. but not 3. The speed dome is too far away 3. Add a terminal resistor. smoothly.
-
Page 45: Appendix 3 24Vac Wire Gauge & Transmission Distance
User Manual of HD-TVI Speed Dome Appendix 3 24VAC Wire Gauge & Transmission Distance The following table describes the recommended Max. distance adopted for the certain wire gauge when the loss rate of 24VAC voltage is less than 10%. For the AC driven device, the maximum voltage loss rate is 10% allowable. -
Page 46: Appendix 4 Wire Gauge Standards
User Manual of HD-TVI Speed Dome Appendix 4 Wire Gauge Standards American Cross-sectional Bare Wire British Wire Wire Gauge Area of Bare Gauge(mm) Gauge SWG Wire(mm 0.750 0.4417 0.800 0.5027 0.900 0.6362 1.000 0.7854 1.250 1.2266 1.500 1.7663 2.000 3.1420 2.500 4.9080 3.000...