HIKVISION DS-2CD63C5G0-IVS User Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. DS-2CD63C5G0-IVS
  6. User manual

HIKVISION DS-2CD63C5G0-IVS User Manual

Network fisheye camera
Hide thumbs Also See for DS-2CD63C5G0-IVS:
Table of Contents

Advertisement

Quick Links

Download this manual
Network Fisheye Camera
User Manual
UD04753B

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION DS-2CD63C5G0-IVS

Summary of Contents for HIKVISION DS-2CD63C5G0-IVS

  • Page 1 Network Fisheye Camera User Manual UD04753B...
  • Page 2 Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
  • Page 3 LOSS DATA DOCUMENTATION, CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL...
  • Page 4 User Manual of Network Fisheye Camera residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
  • Page 5 User Manual of Network Fisheye Camera 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).
  • Page 6 User Manual of Network Fisheye Camera to all the local codes.  Please install blackouts equipment into the power supply circuit for convenient supply interruption.  Please make sure that the ceiling can support more than 50(N) Newton gravities if the camera is fixed to the ceiling.
  • Page 7 User Manual of Network Fisheye Camera  Improper use or replacement of the battery may result in hazard of explosion. Please use the manufacturer recommended battery type. Notes: For the camera supports IR, you are required to pay attention to the following precautions to prevent IR reflection: ...

  • Page 8: Table Of Contents

    User Manual of Network Fisheye Camera Table of Contents Chapter 1 System Requirement ................10 Chapter 2 Network Connection ................11 Setting the Network Camera over the LAN ............11 2.1.1 Wiring over the LAN ....................... 11 2.1.2 Creating a Password ......................12 Setting the Network Camera over the WAN ............
  • Page 9 User Manual of Network Fisheye Camera 5.3.2 Configuring Port Settings ....................54 5.3.3 Configuring PPPoE Settings ..................... 55 5.3.4 Configuring DDNS Settings ....................56 5.3.5 Configuring NAT (Network Address Translation) Settings ..........58 5.3.6 Configuring SNMP Settings ..................... 58 5.3.7 Configuring FTP Settings ....................
  • Page 10 User Manual of Network Fisheye Camera Appendix 2 Port Mapping ..................117 0504051070216...

  • Page 11: Chapter 1 System Requirement

    User Manual of Network Fisheye Camera Chapter 1 System Requirement Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024× 768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version...

  • Page 12: Chapter 2 Network Connection

    User Manual of Network Fisheye Camera Chapter 2 Network Connection Note:  You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center.

  • Page 13: Creating A Password

    User Manual of Network Fisheye Camera  Refer to the Figure 2-2 to set network camera over the LAN via a switch or a router. Figure 2-1 Connecting Directly Figure 2-2 Connecting via a Switch or a Router 2.1.2 Creating a Password You are required to activate the camera first by setting a strong password for it before you can use the camera.
  • Page 14 User Manual of Network Fisheye Camera Figure 2-3 Creating a Password via Web Browser 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
  • Page 15 User Manual of Network Fisheye Camera Select inactive device. Input and confirm password. Figure 2-4 SADP Interface 3. Create a password and input the password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
  • Page 16 User Manual of Network Fisheye Camera Figure 2-5 Modify the IP Address 6. Input the password and click the Save button to activate your IP address modification.  Creating a Password via Client Software The client software is versatile video management software for multiple kinds of devices.
  • Page 17 User Manual of Network Fisheye Camera Figure 2-6 Control Panel 2. Click the Device Management icon to enter the Device Management interface, as shown in the figure below. Figure 2-7 Device Management Interface...
  • Page 18 User Manual of Network Fisheye Camera 3. Check the device status from the device list, and select an inactive device. 4. Click the Activate button to pop up the Activation interface. 5. Create a password and input the password in the password field, and confirm the password.

  • Page 19: Setting The Network Camera Over The Wan

    User Manual of Network Fisheye Camera Figure 2-9 Modifying the Network Parameters 8. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. 9. Input the password to activate your IP address modification. 2.2 Setting the Network Camera over the WAN Purpose: This section explains how to connect the network camera to the WAN with a static IP...

  • Page 20: Dynamic Ip Connection

    User Manual of Network Fisheye Camera 2. Assign a LAN IP address, the subnet mask and the gateway. Refer to Section 2.1.2 for detailed IP address configuration of the network camera. 3. Save the static IP in the router. 4. Set port mapping, e.g., 80, 8000, and 554 ports. The steps for port mapping vary according to the different routers.
  • Page 21 User Manual of Network Fisheye Camera 1. Connect the network camera to the router. 2. In the camera, assign a LAN IP address, the subnet mask and the gateway. Refer to Section 2.1.2 for detailed IP address configuration of the network camera. 3.
  • Page 22 User Manual of Network Fisheye Camera Figure 2-13 Normal Domain Name Resolution Steps: 1. Apply a domain name from a domain name provider. 2. Configure the DDNS settings in the DDNS Settings interface of the network camera. Refer to Section 5.3.4 Configuring DDNS Settings for detailed configuration.

  • Page 23: Chapter 3 Access To The Network Camera

    User Manual of Network Fisheye Camera Chapter 3 Access to the Network Camera 3.1 Accessing by Web Browsers Steps: 1. Open the web browser. 2. Input the IP address of the network camera in the address bar, e.g., 192.168.1.64 and press the Enter key to enter the login interface. 3.

  • Page 24: Accessing By Client Software

    User Manual of Network Fisheye Camera web browser and log in again after installing the plug-in. 3.2 Accessing by Client Software The product CD contains the iVMS-4200 client software. You can view the live video and manage the camera with the software. Follow the installation prompts to install the software.

  • Page 25: Chapter 4 Live View

    User Manual of Network Fisheye Camera Chapter 4 Live View 4.1 Live View Page Purpose: The live view page allows you to view the real-time video, capture images, realize PTZ control, set/call presets and configure video parameters. Log in the network camera to enter the live view page, or you can click Live View on the menu bar of the main page to enter the live view page.
  • Page 26 User Manual of Network Fisheye Camera Menu Bar Live View Window Control Display Stream Type Preset/Patrol Tool Bar Control Setting Setting Figure 4-2 Live View Page (Hardware Decoding) Menu Bar: Click the tab to enter Live View, Playback, Picture, Application and Configuration page respectively.
  • Page 27 User Manual of Network Fisheye Camera Table 4-1 Description of Mount Types Mount Type Icon Description Ceiling mounting. Wall mounting. Table mounting.  Display Mode You can select a display mode for the layout of the live view window. The description of each display mode is shown in the following table.
  • Page 28 User Manual of Network Fisheye Camera Mode Description Mode Description Live view with 1 fisheye view Live view with into 4 PTZ views. and 3 PTZ views. Live view with 1 fisheye view Panorama view. and 8 PTZ views. Live view with a panorama view Live view with a panorama and 3 PTZ views.

  • Page 29: Starting Live View

    User Manual of Network Fisheye Camera Live View Window: Display the live video on the display window of live view. Toolbar: Start/Stop the live view, enable/disable the two-way audio, adjust the audio volume, capture pictures, record the video files, etc.. Note: Icons on tool bar are different under different decoding mode.
  • Page 30 User Manual of Network Fisheye Camera Figure 4-3 Live View Interface (Software Decoding) Figure 4-4 Live View Interface (Hardware Decoding) Table 4-4 Descriptions of Live View Icons Icon Description Start all live view. Stop all live view. Set aspect ratio as 4:3.

  • Page 31: Recording And Capturing Pictures Manually

    User Manual of Network Fisheye Camera Icon Description Set aspect ratio as 16:9. Window size for original video stream. Self-adaptive window size. Window division, 1x1. Window division, 2x2. Window division, 3x3. Manually start/stop recording. Audio on and adjust the volume. Mute.

  • Page 32: Operating Ptz Control

    User Manual of Network Fisheye Camera remote scheduled recording, please refer to Section 6.1 Note: The captured image will be saved as JPEG file or BMP file in your computer. 4.4 Operating PTZ Control Purpose: A PTZ View is a close-up view of some defined area on the panoramic and fisheye view, and it supports digital PTZ control.
  • Page 33 User Manual of Network Fisheye Camera Figure 4-6 PTZ Control Panel Table 4-5 Descriptions of PTZ Control Panel Icon Description Direction buttons Start/stop auto scan Zoom out/Zoom in Focus -/Focus + Iris -/Iris + Adjust speed of pan/tilt movements Enable/disable light Auxiliary Focus Enable/disable wiper Lens initialization...

  • Page 34: Setting/Calling/Deleting A Preset

    User Manual of Network Fisheye Camera Steps: 1. Click to select a PTZ View on the display window, and then the navigation box appears on the Fisheye View and Panorama View. 2. Click the direction arrows on the PTZ control panel. The navigation box will move in the corresponding pan/tilt direction.
  • Page 35 User Manual of Network Fisheye Camera Figure 4-7 Setting a Preset Note: Up to 256 presets are supported.  Calling a Preset: Purpose: The PTZ View of the fisheye camera can directly and quickly move to the area of interest, which is defined as a preset. Before you start: Set the preset.

  • Page 36: Setting/Calling/Deleting A Patrol

    User Manual of Network Fisheye Camera The preset name turns from black to grey. 4.4.3 Setting/Calling/Deleting a Patrol Purpose: A patrol is a scanning track specified by a group of defined presets, with the duration time at each preset separately programmable. Before you start: At least 2 presets are required to set a patrol.
  • Page 37 User Manual of Network Fisheye Camera Note: Up to 32 patrol paths can be set, and each path supporting 16 key points at most.  Calling a Patrol Steps: 1. Click to select a PTZ View on the display window. 2.

  • Page 38: Chapter 5 Network Camera Configuration

    User Manual of Network Fisheye Camera Chapter 5 Network Camera Configuration 5.1 Configuring Local Parameters Purpose: Local configuration provides live view parameters settings, record file settings and picture and clip settings. The recorded videos and captured pictures can be saved on the local PC that runs the web browser.
  • Page 39 User Manual of Network Fisheye Camera for streaming under some network environments. MULTICAST: It’s recommended to select MCAST type when using the Multicast function. For detailed information about Multicast, refer to Section 5.3.1 Configuring TCP/IP Settings.  Live View Performance: Set the live view performance to Shortest Delay or Auto.

  • Page 40: Configuring System Settings

    User Manual of Network Fisheye Camera And click Open to open the set folder. 3. Click Save to save the settings. 5.2 Configuring System Settings 5.2.1 Viewing Basic Information Enter the Basic Information interface: Configuration > System > System Settings > Basic Information In the Basic Information interface, you can edit the Device Name or Device No..

  • Page 41: Time And Dst Settings

    User Manual of Network Fisheye Camera 5.2.2 Time and DST Settings Purpose: You can follow the instructions in this section to configure the time synchronization and DST settings.  Time Settings Steps: 1. Enter the Time Settings interface: Configuration > System > System Settings > Time Settings Figure 5-3 Time Settings 2.
  • Page 42 User Manual of Network Fisheye Camera (3) (Optional) You can click the Test button to test the time synchronization function via NTP server. Figure 5-4 Time Sync by NTP Server Note: If the camera is connected to a public network, you should use a NTP server that has a time synchronization function, such as the server at the National Time Center (IP Address: 210.72.145.44).

  • Page 43: Settings

    User Manual of Network Fisheye Camera time of the device with that of the local PC. 3. Click Save to save the settings.  DST Purpose: For region using the summer time, DST (daylight saving time) settings can be configured according to the actual needs. Steps: 1.

  • Page 44: Settings

    User Manual of Network Fisheye Camera Steps: 1. Enter RS-232 Port Setting interface: Configuration> System > System Settings > RS232 Figure 5-7 RS-232 Settings Note: If you want to connect the camera by the RS-232 port, the parameters of the RS-232 should be exactly the same with the parameters you configured here. 2.

  • Page 45: Upgrade And Maintenance

    User Manual of Network Fisheye Camera the same as the PTZ camera parameters. Figure 5-8 RS-485 Settings 5.2.5 Upgrade and Maintenance Purpose: On Upgrade & Maintenance interface, you can reboot the camera, restore camera parameters, export/import configuration parameters, and upgrade firmware. Enter the Upgrade and Maintenance interface: Configuration >...

  • Page 46: Log Searching

    User Manual of Network Fisheye Camera  Rebooting the Camera Click Reboot to reboot the network camera.  Restoring Default Settings Click Restore or Default to restore the default settings. Note: After restoring the default settings, the IP address is also restored to the default IP address, please be careful for this action.

  • Page 47: System Service Settings

    User Manual of Network Fisheye Camera Please configure network disk for the camera or insert a memory card in the camera. Steps: 1. Enter log searching interface: Configuration > System > Maintenance > Log Figure 5-10 Log Searching Interface 2. Set the log search conditions to specify the search, including the Major Type, Minor Type, Start Time and End Time.

  • Page 48: Authentication

    User Manual of Network Fisheye Camera 5.2.8 Authentication Purpose: You can specifically secure the stream data of live view. Steps: 1. Enter the RTSP Authentication interface: Configuration > System > Security > Authentication Figure 5-12 RTSP Authentication 2. Select the Authentication type basic or disable in the drop-down list to enable or disable the RTSP authentication.
  • Page 49 User Manual of Network Fisheye Camera Figure 5-13 IP Address Filter Interface 2. Check the checkbox of Enable IP Address Filter. 3. Select the type of IP Address Filter in the drop-down list, Forbidden and Allowed are selectable. 4. Set the IP Address Filter list. ...

  • Page 50: Security Service

    User Manual of Network Fisheye Camera (3) Click the OK to finish modifying.  Delete an IP Address or IP Addresses. Select the IP address(es) and click Delete. 5. Click Save to save the settings. 5.2.10 Security Service To enable the remote login, and improve the data communication security, the camera provides the security service for better user experience.
  • Page 51 User Manual of Network Fisheye Camera Figure 5-17 User Information  Adding a User The admin user has all permissions by default and can create/modify/delete other accounts. The admin user cannot be deleted and you can only change the admin password. Steps: 1.
  • Page 52 User Manual of Network Fisheye Camera Figure 5-18 Add a User  Modifying a User Steps: 1. Click the user from the user list and Click Modify. 2. Modify the User Name, Level or Password. 3. Check or uncheck the permissions for the user. 4.

  • Page 53: Open Source Software License

    User Manual of Network Fisheye Camera Figure 5-19 Modify a User  Deleting a User Steps: 1. Click to select the user you want to delete and click Delete. 2. Click OK on the pop-up dialogue box to delete the user. 5.2.12 Open Source Software License You can check the open source software used in this product.

  • Page 54: Configuring Network Settings

    User Manual of Network Fisheye Camera 5.3 Configuring Network Settings 5.3.1 Configuring TCP/IP Settings Purpose: TCP/IP settings must be properly configured before you operate the camera over network. The camera supports both the IPv4 and IPv6. Both versions may be configured simultaneously without conflicting to each other, and at least one IP version should be configured.

  • Page 55: Configuring Port Settings

    User Manual of Network Fisheye Camera and Multicast Address. 3. (Optional) Check the checkbox of Enable Multicast Discovery, and then the online network camera can be automatically detected by client software via private multicast protocol in the LAN. 4. Configure the DNS server. Input the preferred DNS server, and alternate DNS server.

  • Page 56: Configuring Pppoe Settings

    User Manual of Network Fisheye Camera 2. Set the HTTP port, RTSP port and HTTPS port of the camera. HTTP Port: The default port number is 80, and it can be changed to any port No. which is not occupied. RTSP Port: The default port number is 554 and it can be changed to any port No.

  • Page 57: Configuring Ddns Settings

    User Manual of Network Fisheye Camera strongly recommend the use of strong passwords for all functions and network devices. The password should be something of your own choosing (using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers and special characters) in order to increase the security of your product.
  • Page 58 User Manual of Network Fisheye Camera Figure 5-23 DynDNS Settings  NO-IP: Steps: (1) Choose the DDNS Type as NO-IP. Figure 5-24 NO-IP DNS Settings (2) Enter the Server Address as www.noip.com (3) Enter the Domain name you registered. (4) Enter the User Name and Password. (5) Click Save and then you can view the camera with the domain name.

  • Page 59: Configuring Nat (Network Address Translation) Settings

    User Manual of Network Fisheye Camera 5.3.5 Configuring NAT (Network Address Translation) Settings Purpose: NAT interface allows you to configure the UPnP™ parameters. Universal Plug and Play (UPnP™) is a networking architecture that provides compatibility among networking equipment, software and other hardware devices. The UPnP protocol allows devices to connect seamlessly and to simplify the implementation of networks in the home and corporate environments.
  • Page 60 User Manual of Network Fisheye Camera You can set the SNMP function to get camera status, parameters and alarm related information and manage the camera remotely when it is connected to the network. Before you start: Before setting the SNMP, please download the SNMP software and manage to receive the camera information via SNMP port.
  • Page 61 User Manual of Network Fisheye Camera Figure 5-26 SNMP Settings 2. Check the checkbox of Enable SNMPv1, Enable SNMP v2c, or Enable SNMPv3 to enable the feature correspondingly. 3. Configure the SNMP settings. Note: The settings of the SNMP software should be the same as the settings you configure here.

  • Page 62: Configuring Ftp Settings

    User Manual of Network Fisheye Camera 5.3.7 Configuring FTP Settings Purpose: You can configure the FTP server related information to enable the uploading of the captured pictures to the FTP server. The captured pictures can be triggered by events or a timing snapshot task. Steps: 1.

  • Page 63: Email Settings

    User Manual of Network Fisheye Camera responsibility of the installer and/or end-user. Directory: In the Directory Structure field, you can select the root directory, parent directory and child directory. When the parent directory is selected, you have the option to use the Device Name, Device Number or Device IP for the name of the directory;...
  • Page 64 User Manual of Network Fisheye Camera Note: Please refer to Section 5.3.1 Configuring TCP/IP Settings for detailed information. 2. Enter the Email Settings interface: Configuration > Network >Advanced Settings > Email Figure 5-28 Email Settings 3. Configure the following settings: Sender: The name of the email sender.

  • Page 65: Configuring Https Settings

    User Manual of Network Fisheye Camera pictures. Authentication (optional): If your email server requires authentication, check this checkbox to use authentication to log in to this server and input the login user name and password.  For your privacy and to better protect your system against security risks, we strongly recommend the use of strong passwords for all functions and network devices.
  • Page 66 User Manual of Network Fisheye Camera Configuration > Network > Advanced Settings > HTTPS Figure 5-29 HTTPS Settings 2. Check the checkbox of Enable to enable the function. 3. Install a certificate. There are three ways of installation available, choose one according to your actual need.
  • Page 67 User Manual of Network Fisheye Camera If you already have had a signed certificate, select this installation method, and start installation according to pop-up installation guides.  Create the authorized certificate. Figure 5-31 Create the Certificate Request and Continue Installation (1) Select Create the certificate request first and continue the installation as the installation method.

  • Page 68: Configuring Qos Settings

    User Manual of Network Fisheye Camera 5.3.10 Configuring QoS Settings Purpose: QoS (Quality of Service) can help solve the network delay and network congestion by configuring the priority of data sending. Steps: 1. Enter the QoS Settings interface: Configuration > Network > Advanced Settings >...
  • Page 69 User Manual of Network Fisheye Camera Before you start: The authentication server must be configured. Please apply and register a user name and password for 802.1X in the server.  For your privacy and to better protect your system against security risks, we strongly recommend the use of strong passwords for all functions and network devices.

  • Page 70: Configuring Video And Audio Settings

    User Manual of Network Fisheye Camera Note: A reboot is required for the settings to take effect. 5.4 Configuring Video and Audio Settings 5.4.1 Configuring Video Settings Steps: 1. Enter the Video Settings interface: Configuration > Video/Audio > Video 2. Select the camera channel from Channel No. drop-down list. 3.
  • Page 71 User Manual of Network Fisheye Camera Video Type: Select the stream type to video stream, or video & audio composite stream. The audio signal will be recorded only when the Video Type is Video & Audio. Resolution: Select the resolution of the video output. Bitrate Type: Select the bitrate type to constant or variable.
  • Page 72 User Manual of Network Fisheye Camera maximum average bitrate. Compared to H.264, H.264+ reduces storage by up to 50% with the same maximum bitrate in most scenes. You need to reboot the camera if you want to turn on or turn off the H.264+. Max.

  • Page 73: Configuring Audio Settings

    User Manual of Network Fisheye Camera It refers to the smoothness of the stream. The higher value of the smoothing, the better fluency of the stream is, though, the video quality may not be so satisfactory. The lower value of the smoothing, the higher quality of the stream is, though it may appear not fluent.

  • Page 74: Configuring Roi Encoding

    User Manual of Network Fisheye Camera Note: The audio settings vary according to the camera model. 5.4.3 Configuring ROI Encoding Purpose: ROI stands for the region of interest. And the ROI encoding enables you to discriminate between the ROI and background information in compression, that is to say, the technology assigns more encoding resource to the region of interest to increase the quality of the ROI whereas the background information is less focused.
  • Page 75 User Manual of Network Fisheye Camera Figure 5-37 Region of Interest Settings Notes: • ROI level means the image quality enhancing level. The larger the value is, the better the image quality would be. • For PTZ camera channels decoded by hardware, you can use the PTZ panel to adjust view angles when drawing fixed regions.

  • Page 76: Configuring Image Parameters

    User Manual of Network Fisheye Camera 5.5 Configuring Image Parameters 5.5.1 Configuring Display Settings Purpose: You can set the image quality of the camera, including brightness, contrast, saturation, sharpness, etc. Steps: 1. Enter the Display Settings interface: Configuration > Image> Display Settings 2.
  • Page 77 User Manual of Network Fisheye Camera Saturation describes the colorfulness of the image color, which ranges from 1 to 100, and the default value is 50. Sharpness describes the edge contrast of the image, which ranges from 1 to 100, and the default value is 50. ...
  • Page 78 User Manual of Network Fisheye Camera over-exposure. When the light is turned on, and Auto and Manual are selectable for IR mode. Select AUTO, and the IR LED changes according to the actual luminance. E.g., if the current scene is bright enough, then the IR LED adjusts itself to lower power;...

  • Page 79: Configuring Osd Settings

    User Manual of Network Fisheye Camera NTSC standard. Note: The display parameters vary according to the different camera model. Please refer to the actual interface for details. Day/Night Scheduled Switch Day/Night scheduled-switch configuration interface enables you to set the camera parameters for day and night separately, guaranteeing the image quality in different illumination.
  • Page 80 User Manual of Network Fisheye Camera OSD (On-screen Display) refers to the camera name, time/date format, display mode, and OSD size displayed on the live view. Steps: 1. Enter the OSD Settings interface: Configuration > Image > OSD Settings Figure 5-40 OSD Settings 2.

  • Page 81: Configuring Privacy Mask

    User Manual of Network Fisheye Camera 7. You can use the mouse to click-and-drag the red text frames in the live view window to adjust the OSD position. 8. (Optional) Click Copy to to copy the parameters of set camera channels to other channels.

  • Page 82: Picture Overlay

    User Manual of Network Fisheye Camera 2. Select a camera channel to configure. 3. Check the checkbox of Enable Privacy Mask to enable this function. 4. Click the Draw Area button to start drawing. 5. Click-and-drag the mouse in the live video window to draw the mask area. 6.

  • Page 83: Display Info. On Stream

    User Manual of Network Fisheye Camera 5. Drag the red rectangle to adjust the position. 6. Click Save to save settings. Note: The picture must be in RGB24 bmp format and the maximum picture size is 128*128. 5.5.5 Display Info. on Stream Check the checkbox of Enable Dual-VCA, and the information of the objects (e.g.
  • Page 84 User Manual of Network Fisheye Camera Motion detection detects the moving objects in the configured surveillance area, and a series of actions can be taken when the alarm is triggered. In order to detect the moving objects accurately and reduce the false alarm rate, normal configuration and expert configuration are selectable for different motion detection environment.
  • Page 85 User Manual of Network Fisheye Camera Figure 5-44 Motion Detection Settings 2. Check the checkbox of Enable Motion Detection. 3. (Optional) Check the checkbox of Enable Dynamic Analysis for Motion if you want to mark the detected objects with green rectangles on the live view window.
  • Page 86 User Manual of Network Fisheye Camera 6. (Optional) Move the slider to set the sensitivity of the detection. Task 2: Set the Arming Schedule for Motion Detection Steps: 1. Click Arming Schedule to edit the arming schedule. Figure 5-45 Arming Schedule Setting 2.
  • Page 87 User Manual of Network Fisheye Camera Figure 5-46 Linkage Method Settings  Audible Warning Trigger the audible warning locally. And it only supported by the device that has the audio output.  Notify Surveillance Center: Send an exception or alarm signal to remote management software when an event occurs.
  • Page 88 User Manual of Network Fisheye Camera  Smart Tracking: It can make the speed dome to track target manually by clicking the target on the live view of fisheye camera. Note: In order to make smart tracking take effect, you need to have a speed dome which has auto tracking function installed near your fisheye camera, and you have to configure relevant settings on 4200 Client Software.
  • Page 89 User Manual of Network Fisheye Camera If Expert is selected as the configuration mode, different sets of parameters are adopted for motion detection at day and night. ● Day/Night Switch OFF Steps: (1) Draw the detection area as in the normal configuration mode. The supported area number varies according to different camera models.

  • Page 90: Configuring Video Tampering Alarm

    User Manual of Network Fisheye Camera (7) Click Save to save the settings. ● Day/Night Scheduled-Switch Steps: (1) Draw the detection area as in the normal configuration mode. The supported area number varies according to different camera models. (2) Select Scheduled-Switch for Switch Day and Night Settings. (3) Select the start time and end time for the switching timing.

  • Page 91: Configuring Alarm Input

    User Manual of Network Fisheye Camera Figure 5-48 Video Tampering Detection Settings 3. Draw the detection area as in the normal configuration mode. 4. Move the slider to set the sensitivity. 5. Click Arming Schedule to set arming schedule as that in Task 2 Set the Arming Schedule for Motion Detection in Section 5.6.1.

  • Page 92: Configuring Alarm Output

    User Manual of Network Fisheye Camera Figure 5-49 Alarm Input Settings 2. Choose the alarm input No. and the Alarm Type. The alarm type can be NO (Normally Open) and NC (Normally Closed). Edit the alarm name (optional). 3. Check the checkbox of Enable Alarm Input Handling to enable the function. 4.
  • Page 93 User Manual of Network Fisheye Camera 1. Enter the Alarm Output Settings interface: Configuration > Events > Basic Event > Alarm Output 2. Select one alarm output channel in the Alarm Output drop-down list. 3. (Optional) Input the alarm output name in the text field. 4.

  • Page 94: Handling Exception

    User Manual of Network Fisheye Camera Note: Alarm output settings vary according to the camera model. 5.6.5 Handling Exception The exception type can be HDD full, HDD error, network disconnected, IP address conflicted and illegal login to the cameras. Steps: 1.
  • Page 95 User Manual of Network Fisheye Camera 3. Select the line from the dropdown list for detection setting. 4. Click the Draw Area button, and a virtual line is displayed on the live video. Figure 5-52 Line Crossing Detection Setting 5. Click-and-drag the line, and you can locate it on the live video as desired. Click on the line, two red squares are displayed on each end, and you can click-and-drag one of the red squares to define the shape and length of the line.

  • Page 96: Configuring Intrusion Detection

    User Manual of Network Fisheye Camera can be detected. 7. Click-and-drag the slider to set the detection sensitivity. Sensitivity: Range [1 to 100]. The higher the value is, the more easily the line crossing action can be detected. 8. You can click the Clear button to clear the pre-defined line. 9.
  • Page 97 User Manual of Network Fisheye Camera detection. Threshold: Range [0 to 10]s, the threshold for the time of the object loitering in the region. If you set the value as 0, alarm is triggered immediately after the object entering the region. Sensitivity: Range [1 to 100].

  • Page 98: Configuring Heat Map

    User Manual of Network Fisheye Camera Figure 5-53 Intrusion Detection Settings 7. Repeat the above steps to configure other regions. Up to 4 regions can be set. You can click the Clear button to clear all pre-defined regions. 8. You can click the Clear button to clear the pre-defined region. 9.
  • Page 99 User Manual of Network Fisheye Camera dynamic environment. You should set a comparatively higher value if the monitoring scene changes fast. Setting the level properly will avoid the misinformation. The default level is 50. Minimum Target Size [0 to 100]: It refers to the minimum target size that can be recognized and counted in a heat map.
  • Page 100 User Manual of Network Fisheye Camera 6. Go to Linkage Method tab, and select the linkage method by checking the checkbox of notify the surveillance center. 7. Click Save to save the settings. Notes: • The heat map statistics will be calculated under Application tab. Go to Application to check the heat map statistics.

  • Page 101: Chapter 6 Storage Settings

    User Manual of Network Fisheye Camera Chapter 6 Storage Settings 6.1 Configuring Recording Schedule Purpose: There are two kinds of recording for the cameras: manual recording and scheduled recording. For the manual recording, refer to Section 4.3 Recording and Capturing Pictures Manually.
  • Page 102 User Manual of Network Fisheye Camera Figure 6-2 Record Parameters Pre-record: The time you set to start recording before the scheduled time or the event. For example, if an alarm triggers recording at 10:00, and the pre-record time is set as 5 seconds, the camera starts to record at 9:59:55. The Pre-record time can be configured as No Pre-record, 5 s, 10 s, 15 s, 20 s, 25 s, 30 s or not limited.
  • Page 103 User Manual of Network Fisheye Camera  Record Triggered by Motion Detection If you select Motion, the video will be recorded when the motion is detected. Besides configuring the recording schedule, you have to set the motion detection area and check the checkbox of Trigger Channel in the Linkage Method of Motion Detection Settings interface.
  • Page 104 User Manual of Network Fisheye Camera and check the checkbox of Trigger Channel in the Linkage Method of Line Crossing Detection Settings interface. For detailed information, please refer to Section 5.6.6 Configuring Line Crossing Detection.  Record Triggered by Intrusion Detection If you select Intrusion Detection, the video will be recorded when the intrusion event is detected.

  • Page 105: Configuring Capture Setting

    User Manual of Network Fisheye Camera 6.2 Configuring Capture Setting Purpose: You can configure the scheduled capture and event-triggered capture. The captured picture can be stored in the SD card (if supported) or in the network disk (For details, please refer to Section 6.3 Configuring Net HDD). The captured pictures can also be uploaded to a FTP server.

  • Page 106: Configuring Net Hdd

    User Manual of Network Fisheye Camera the events, including motion detection, alarm input, line crossing detection and intrusion detection. For details, please refer to Section 5.6. 4) Select the picture format, resolution, quality, capture interval, and capture number. 5. Set the time interval between two snapshots. 6.
  • Page 107 User Manual of Network Fisheye Camera Note: Please refer to the NAS User Manual for creating the file path.  For your privacy and to better protect your system against security risks, we strongly recommend the use of strong passwords for all functions and network devices.
  • Page 108 User Manual of Network Fisheye Camera When the initialization completed, the status of disk will become Normal. Figure 6-7 View Disk Status 3. Define the quota for record and pictures. (1) Input the quota percentage for picture and for record. (2) Click Save and refresh the browser page to activate the settings.

  • Page 109: Chapter 7 Playback

    User Manual of Network Fisheye Camera Chapter 7 Playback Purpose: This section explains how to view the remotely recorded video files stored in the network disks or SD cards. Note: You can also search the records files and play it back in different playback modes via iVMS-4200 client software.
  • Page 110 User Manual of Network Fisheye Camera Figure 7-2 Search Video 3. Choose a display mode to play the video. Figure 7-3 Playback Display Mode Setting Note: For detailed description of each display mode, refer to Section 4.1 Live View Page. 4.
  • Page 111 User Manual of Network Fisheye Camera Button Operation Button Operation Start/Stop clipping video Pause files Stop Playback by frame Audio on and adjust Slow Forward volume/Mute Fast Forward Download Enable/Disable digital Stop all playback zoom Play with full screen Notes: ...

  • Page 112: Chapter 8 Picture

    User Manual of Network Fisheye Camera Chapter 8 Picture Click Picture to enter the picture searching interface. You can search, view, and download the pictures stored in the local storage or network storage. Notes:  Make sure HDD, NAS or memory card are properly configured before you process picture searching.

  • Page 113: Chapter 9 Application

    User Manual of Network Fisheye Camera Chapter 9 Application Click Application to enter the heat map statistics interface. You can search, view, and download the counting data stored in the local storage or network storage. 9.1 Heat Map Statistics Purpose: Heat map is a graphical representation of data represented by colors.
  • Page 114 User Manual of Network Fisheye Camera The duration displayed next to “High” or “Low” stands for the cumulative time that the area keeps certain level of visit frequency. Figure 9-1 Space Heat Map Time Heat Map: The heat value of the pre-defined area is calculated by hour, day, or month. You can click the Export button to export the data in an excel file.
  • Page 115 User Manual of Network Fisheye Camera Note: It is recommended that you do not adjust the electronic lens after the installation is completed, which may cause the inaccuracy of the data in some degree.

  • Page 116: Appendix

    User Manual of Network Fisheye Camera Appendix Appendix 1 SADP Software Introduction  Description of SADP SADP (Search Active Devices Protocol) is a kind of user-friendly and installation-free online device search tool. It searches the active online devices within your subnet and displays the information of the devices.
  • Page 117 User Manual of Network Fisheye Camera  Search online devices manually You can also click Refresh button to refresh the online device list manually. The newly searched devices will be added to the list. You can click on each column heading to order the information; you can click to expand the device table and hide the network parameter panel on the right side, or click...
  • Page 118 User Manual of Network Fisheye Camera Appendix 2 Port Mapping The following settings are for TP-LINK router (TL-WR641G). The settings vary depending on different models of routers. Steps: 1. Select the WAN Connection Type, as shown below: Figure A.2.1 Select the WAN Connection Type 2.
  • Page 119 User Manual of Network Fisheye Camera another camera as 81, 8001, 555, 8201 with IP 192.168.1.24. Refer to the steps as below: Steps: 1. As the settings mentioned above, map the port 80, 8000, 554 and 8200 for the network camera at 192.168.1.23 2.
  • Page 120 User Manual of Network Fisheye Camera...

Table of Contents