Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HIKVISION UD.6L0201B1295A01
Summary of Contents for HIKVISION UD.6L0201B1295A01
- Page 1 Network Convert Camera Quick Operation Guide UD.6L0201B1295A01...
- Page 2 Network Convert Camera·Quick Operation Guide Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. About This Document This manual applies to the following camera models. Model DS-2CD6412FWD-10 DS-2CD6412FWD-20 DS-2CD6412FWD-30 This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice.
-
Page 3: Regulatory Information
Network Convert Camera·Quick Operation Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 4 Network Convert Camera·Quick Operation Guide 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.
-
Page 5: Safety Instruction
Network Convert Camera·Quick Operation Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. - Page 6 Network Convert Camera·Quick Operation Guide ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed.
- Page 7 Network Convert Camera·Quick Operation Guide ● Do not place the camera in extremely hot, cold (the operating temperature shall be-30°C ~+60°C,or -40°C ~ 60°C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation.
-
Page 8: Table Of Contents
Network Convert Camera·Quick Operation Guide Table of Contents 1 Appearance Description ..............8 2 Installation ..................12 2.1 Installation of Block-Shaped Sensor Unit ....... 15 2.1.1 Concealed Mounting .......... 15 2.1.2 Exposed Mounting ..........17 2.2 Installation of Cylindrical Sensor Unit ......19 2.3 Installation of Fixed Focal Unit ........ -
Page 9: Appearance Description
Network Convert Camera·Quick Operation Guide 1 Appearance Description Camera Description The overview of the network bullet camera is shown below: 2 3 4 VIN1 AUDIO AUDIO LAN(PoE) RXD TXD GND IN1 1B 1A DC 12V RESET Figure 1-1 The Covert Camera with Block-shaped Sensor Unit... - Page 10 Network Convert Camera·Quick Operation Guide 2 3 4 VIN1 AUDIO AUDIO LAN(PoE) RXD TXD GND IN1 1B 1A DC 12V RESET Figure 1-2 The Covert Camera with Cylindrical Sensor Unit 2 3 4 VIN1 AUDIO AUDIO LAN(PoE) RXD TXD GND IN1 1B 1A DC 12V RESET Figure 1-3...
- Page 11 Network Convert Camera·Quick Operation Guide Table 1-1 Description of the Camera Description Description Main Unit PoE & Network Power Indicator LED Mounting Rail Block-Shaped Sensor Status Indicator LED Unit Link Indicator Led Decorative Cover Audio Interface Straight Mounting Bracket RJ-12 Cable Cylindrical Sensor Unit Micro SD Card Slot RJ-12 Interface...
- Page 12 Network Convert Camera·Quick Operation Guide Color& Indicator Status Solid red On normal operation POWER Unlit Power Off Solid green Camera works properly STATUS Camera does not work Unlit properly. Flashing Network connection is amber functioning properly LINK Unlit No network connection...
-
Page 13: Installation
Network Convert Camera·Quick Operation Guide 2 Installation Before you start: Make sure the device in the package is in good condition and all the assembly parts are included. Make sure all the related equipment is power-off during the installation. - Page 14 Network Convert Camera·Quick Operation Guide ● Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection. ● The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS.
- Page 15 Network Convert Camera·Quick Operation Guide For cement surface mounting, you need to use the expansion screw to fix the camera. For wooden surface mounting, you can just use the self-tapping screw to fix the camera. Hang the hook which is on upper-side of the main unit onto the rail, press a little harder on the lower part of the main unit, and then the elastic clasp will be automatically buckled.
-
Page 16: Installation Of Block-Shaped Sensor Unit
Network Convert Camera·Quick Operation Guide If you already had a standard rail installed, you can buckle the main unit onto the installed rail directly. As shown in figure below. Figure 2-3 Buckle the Main Unit onto Standard Rail Installation of Block-Shaped Sensor Unit This series of camera support concealed mounting and exposed mounting with a decorative cover. - Page 17 Network Convert Camera·Quick Operation Guide Figure 2-4 Drill on the Surface Make sure the drilling hole is big enough for the camera lens. Remove a side of the adhesive tape on the bracket. Paste the bracket on mounting surface by aligning with the drilled hole. Figure 2-5 Paste the Bracket...
-
Page 18: Exposed Mounting
Network Convert Camera·Quick Operation Guide Install the block-shaped sensor unit into the bracket and make it to be buckled. Tighten the fastening screw on the top of the bracket. Figure 2-6 Insert the Block-shaped Sensor Unit 2.1.2 Exposed Mounting Steps: Fix the Block-shaped sensor unit on the mounting surface with screws. - Page 19 Network Convert Camera·Quick Operation Guide Figure 2-7 Fix the Block-shaped Sensor Unit For cement surface mounting, you need to use the expansion screw to fix the camera. For wooden surface mounting, you can just use the self-tapping screw to fix the camera. Shield the sensor unit with the decorative cover.
-
Page 20: Installation Of Cylindrical Sensor Unit
Network Convert Camera·Quick Operation Guide Figure 2-8 Hood the Cover 2.2 Installation of Cylindrical Sensor Unit This series of camera only support concealed mounting. Please make sure that the mounting surface is suitable for adhesive pasting. Steps: Drill on the mounting surface. As shown in figure below. - Page 21 Network Convert Camera·Quick Operation Guide Figure 2-9 Drill on the Surface Make sure that the drilling hole is big enough for the camera lens. 2. Remove a side of the adhesive tape on the bracket. Paste the bracket on the mounting surface with aligning with the drilling hole.
-
Page 22: Installation Of Fixed Focal Unit
Network Convert Camera·Quick Operation Guide 4. Turn the locking sleeve to fix the sensor. Figure 2-11 Install the Cylindrical Sensor 2.3 Installation of Fixed Focal Unit Steps: 1. Fix the mounting base of the bracket to the ceiling with the supplied screws. - Page 23 Network Convert Camera·Quick Operation Guide Figure 2-13 Hood the Bracket Cover 3. Screw the bracket to the mounting base. Figure 2-14 Screw the Bracket...
- Page 24 Network Convert Camera·Quick Operation Guide Another shorter bracket is also selectable, please select the bracket according to your demand. 4. Loop the fixed focal unit with the loop of the bracket, and tighten it with the supplied screw. As shown in Figure 2-15. Figure 2-15 Loop the Fixed Focal Unit 5.
- Page 25 Network Convert Camera·Quick Operation Guide Figure 2-16 Install the Fixed Focal Unit to the Bracket 6. Loosen the knob to adjust the surveillance angle, and then tighten the lock nut to complete the installation. Knob Lock Nut Figure 2-17 Complete the Installation...
-
Page 26: Setting The Network Camera Over The Lan
Network Convert Camera·Quick Operation Guide 3 Setting the Network Camera over the Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP or PCNVR software to search and change the IP of network camera. - Page 27 Network Convert Camera·Quick Operation Guide Use PCNVR software and to list the online devices. Please refer to the user manual of PCNVR client software for detailed information. 2. Change the IP address and subnet mask to the same subnet as of your PC.
- Page 28 Network Convert Camera·Quick Operation Guide Figure 3-2 Search Online Devices Device can be searched and displayed in the list in 15 seconds after it goes online; it will be removed from the list in 45 seconds after it goes offline. Search online devices manually: You can also click to refresh the online device...
-
Page 29: Modify Device Information
Network Convert Camera·Quick Operation Guide You can click on each column heading to order the information; you can click to show the device table and hide the network parameter panel on the right side, or click to show the network parameter panel. ... - Page 30 Network Convert Camera·Quick Operation Guide Figure 3-4 Modify Network Parameters 3. Enter the IP address of network camera in the address field of the web browser to view the live video. The default value of the IP address is “192.0.0.64”. The default user name is “admin”, and password is “12345”.
-
Page 31: Accessing Via Web Browser
Network Convert Camera·Quick Operation Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 6.0 and above version, Apple Safari... - Page 32 Network Convert Camera·Quick Operation Guide Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
- Page 33 Network Convert Camera·Quick Operation Guide Figure 4-2 Download Plug-in Figure 4-3 Install Plug-in (1)
- Page 34 Network Convert Camera·Quick Operation Guide Figure 4-4 Install Plug-in (2) 6. Reopen the web browser after the installation of the plug-in and repeat steps 2-4 to login. For detailed instructions of further configuration, please refer to the user manual of network camera.