Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-2CC52H1T-FITS
Summary of Contents for HIKVISION DS-2CC52H1T-FITS
- Page 1 HD Fisheye Camera User Manual UD01467B...
-
Page 2: Regulatory Information
Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. This manual applies to the model DS-2CC52H1T-FITS. This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. - Page 3 2. This device must accept any interference received, including interference that may cause undesired operation EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2014/35/EU, the EMC Directive 2014/30/EU.
- Page 4 1 Introduction 1.1 Product Features This series of camera adopts high performance sensor and advanced circuit board design technology. It features high resolution, low distortion, and low noise, etc. It is suitable for surveillance system and image process system. 5 Megapixel high-performance CMOS ...
-
Page 5: Installation
2 Installation Before you start: Please make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the installation environment. - Page 6 2. Align the screw holes and cable hole on the drill template and the base plate, and then fix the base plate to the ceiling with the two supplied screws. Notes: ● For cement wall, you need to use the expansion screw to fix the mount.
- Page 7 cables including power cable, network cable, audio and alarm cables, etc. 4. Align the triangle mark on the camera and base plate, and then rotate the camera clockwise until it is locked up by the three bayonet joints on the base plate. 5.
-
Page 8: Wall Mounting With A Slant Mounting Base
2.2 Wall Mounting with a Slant Mounting Base Before you start: You need to purchase a slant mounting base separately if this mounting method is selected. Steps: 1. Drill two screw holes and the cable hole according to the supplied drill template. 2-26 φ24 φ102... - Page 9 3. Align the screw holes on the slant mounting base and the base plate, and then secure the base plate on the slant mounting base with the two supplied screws. 4. Route the cables through the cable hole or the side opening according to the actual needs, and connect the corresponding cables including power cable, network cable, audio and alarm cables, etc.
-
Page 10: Wall Mounting With A Bracket
7. To disassemble the camera: Press the Push button on the base plate, rotate the camera anticlockwise, and then you can remove the camera from the base plate. PUSH 2.3 Wall Mounting with a Bracket Before you start: You need to purchase the bracket separately if this mounting method is selected. - Page 11 2. Fix the mounting base to the wall with the screws. 3. Align the screw holes on the bracket and the base plate, and then secure the base plate on the bracket with the two supplied screws.
- Page 12 4. Route the cables through the cable hole according to the actual needs, and connect the corresponding cables including power cable, network cable, audio and alarm cables, etc. 5. Align the triangle mark on the camera and base plate, and then rotate the camera clockwise until it is locked up by the three bayonet joints on the base plate.
- Page 13 2.4 Pendant Mounting with a Bracket Before you start: You have to purchase the bracket separately if this mounting method is selected. Steps: 1. Fix the pendant bracket to the wall with the supplied M6×65 screws. 2. Aim the screwed hole on the camera at the top of the pendant bracket, and then rotate the camera until it is secured tightly.
-
Page 14: Operation
3. Loosen the knob on the bracket and adjust the camera body to get the desired surveillance angle. Tighten the knob on bracket to secure the camera. 3 Operation 3.1 Menu Description Setup FACTORY MAIN MENU INSTALLATION DEFAULT EXIT VIDEO CEILING WALL DAY&NIGHT... - Page 15 Notes: ● With a camera controller (purchased separately) or calling the preset No. 95 of DVR you can select the menu and adjust the parameters. ● Move the cursor up/down/left/right with PTZ control panel to select the menu item. ● Press the OK key or click Iris+ to confirm a selection. 3.2 INSTALLATION The installation allows user to select different working environments.
- Page 16 DEFAULT Select DEFAULT to play live view in original view. PANORAMA Select PANORAMA to play live view after dewraping. 4 PTZ Select 4 PTZ to play live view in 4 PTZ panel mode. Move the cursor to select the PTZ panel to adjust and confirm. Click up-left or up-right to rotate the PTZ panel.
-
Page 17: Wall Mounting
ANNULAR ANNULAR ANNULAR PANEL 1 ANNULAR PANEL 2 SAVE & EXIT RETURN Select ANNULAR to play live view in two annular panels of after-dewraping image. MINI-FISHEYE & 1 PTZ Select DEFAULT to play live view in one fisheye mode and one PTZ panel view. -
Page 18: Day & Night
DEFAULT Select DEFAULT to play live view in original view. PANORAMA Select PANORAMA to play live view after dewraping. 4 PTZ Select 4 PTZ to play live view in 4 PTZ panel mode. Move the cursor to select the PTZ panel to adjust and confirm. Click up-left or up-right to rotate the PTZ panel. -
Page 19: Video Setting
AUTO The image switches between color mode and black/white mode automatically. COLOR The image is colored in day mode all the time. The image is black and white all the time. 3.3.2 INFRARED Turn on/off the INFRARED by moving the cursor. 3.3.3 VIDEO SETTING BRIGHTNESS This feature is used to adjust brightness of the image. -
Page 20: Save And Exit
SATURATION This feature is used to adjust color saturation of the image. The value ranges from 0 to 100. 3.3.4 RESET MAIN MENU Select RESET MAIN MENU to reset all parameters of main menu to the default value. 3.3.5 SAVE & EXIT Select SAVE &...