Related Manuals for Epson S1D13706
Summary of Contents for Epson S1D13706
- Page 1 All manuals and user guides at all-guides.com S1D13706 Embedded Memory LCD Controller S5U13706P00C100 Evaluation Board User Manual Document Number: X31B-G-021-01.2 Rev. 1.2...
- Page 2 This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a consumer product. The user should use it properly and in a safe manner. Seiko Epson does not assume any responsibility or liability of any kind of damage and/or fire caused by the use of it.
-
Page 3: Table Of Contents
..... . 16 S1D13706 Embedded Memory ......16 Software Adjustable LCD Backlight Intensity Support Using PWM . - Page 4 All manuals and user guides at all-guides.com Seiko Epson Corporation S5U13706P00C100 Evaluation Board Rev. 1.2...
-
Page 5: Introduction
1 Introduction This manual describes the setup and operation of the S5U13706P00C100 Evaluation Board. The board is designed as an evaluation platform for the S1D13706 Embedded Memory LCD Controller. This document is updated as appropriate. Please check for the latest revision of this document before beginning any development. -
Page 6: Features
• 4/8/16-bit 3.3V or 5V single color passive LCD panel support. • 9/12/18-bit 3.3V or 5V active matrix TFT LCD panel support. • Direct interface for 18-bit Epson D-TFD LCD panel support. • Direct interface for 18-bit Sharp HR-TFT LCD panel support. -
Page 7: Installation And Configuration
3.1 Configuration DIP Switches The S1D13706 has configuration inputs (CNF[7:0]) which are read on the rising edge of RESET#. In order to configure the S1D13706 for multiple Host Bus Interfaces a ten- position DIP switch (S1) is provided. The following figure shows the location of DIP switch SW1 on the S5U13706P00C100. - Page 8 All manuals and user guides at all-guides.com Installation and Configuration The S1D13706 has 8 configuration inputs (CNF[7:0]) which are read on the rising edge of RESET#. All S1D13706 configuration inputs are fully configurable using a ten position DIP switch as described below.
-
Page 9: Configuration Jumpers
HR-TFT and D-TFD panels as GPIO0 is required for both panels. For details, refer to the S1D13706 Hardware Functional Specification, document number X31B-A-001-xx. Note When configured for Sharp HR-TFT or Epson D-TFD panels, JP1 must be set to no jumper and JP6 must be set to position 2-3. GPIO0 connected GPIO0 disconnected... - Page 10 Position 1-2 sets the voltage level to 5.0V. Position 2-3 sets the voltage level to 3.3V (default setting). Note When configured for Sharp HR-TFT or Epson D-TFD panels, JP1 must be set to no jumper and JP6 must be set to position 2-3. 5.0V 3.3V...
-
Page 11: Cpu Interface
RESET# Note A0 for these busses is not used internally by the S1D13706. If the target MC68K bus is 32-bit, then these signals should be connected to D[31:16]. These pins are not used in their corresponding Host Bus Interface mode. Systems are... -
Page 12: Cpu Bus Connector Pin Mapping
CPU Bus Connector Pin Mapping Table 4-2: CPU Bus Connector (H3) Pinout Connector Comments Pin No. Connected to DB0 of the S1D13706 Connected to DB1 of the S1D13706 Connected to DB2 of the S1D13706 Connected to DB3 of the S1D13706 Ground... - Page 13 Table 4-3: CPU Bus Connector (H4) Pinout Connector Comments Pin No. Connected to A0 of the S1D13706 Connected to A1 of the S1D13706 Connected to A2 of the S1D13706 Connected to A3 of the S1D13706 Connected to A4 of the S1D13706...
-
Page 14: Lcd Interface Pin Mapping
FPDATxx signals at the first valid edge of FPSHIFT. For further FPDATxx to LCD interface mapping, see the S1D13706 Hardware Functional Specification, document number X31B-A-001-xx. GPO on H1 can be inverted by setting JP4 to 2-3. - Page 15 If REG[10h] bits 1-0 are set for either HR-TFT or D-TFD, some of the pins are used for the HR-TFT or D-TFD interfaces and are not available as GPIO pins. Seiko Epson Corporation S5U13706P00C100 Evaluation Board Rev. 1.2...
-
Page 16: Technical Description
6.3 S1D13706 Embedded Memory The S1D13706 has 80K bytes of embedded SRAM. The 80K byte display buffer address space is directly and contiguously available through the 17-bit address bus. 6.4 Software Adjustable LCD Backlight Intensity Support Using PWM The S1D13706 provides Pulse Width Modulation output on PWMOUT. -
Page 17: Passive/Active Lcd Panel Support
The buffered LCD connector (H1) provides the same LCD panel signals as those directly from S1D13706, but with voltage-adapting buffers selectable to 3.3V or 5.0V. Pin 32 on this connector provides a voltage level of 3.3V or 5.0V to the LCD panel logic (see “JP6 - LCD Panel Voltage”... -
Page 18: Parts List
Do not populate JP2, JP3, HEADER 3 header Shielded SMT power Do not purchase. Do not L2, L1 47uH inductor, +/-20%, 1.17A, populate. 0.18 ohm Do not purchase. Do not MMBT3906 PNP Transistor / SOT-23 populate. Seiko Epson Corporation S5U13706P00C100 Evaluation Board Rev. 1.2... - Page 19 S1D13706F00A mount package 5V fixed voltage regulator, Do not purchase. Do not LT1117CST-5 SOT-223 populate. TI 74AHC04, SO-14 74AHC04 SO-14 package package Do not purchase. Do not ICD2061A Wide SO-16 package populate. Seiko Epson Corporation S5U13706P00C100 Evaluation Board Rev. 1.2...
- Page 20 0805 Resistor, 0 ohm side to short pins 2-3 of 0ohm JP2 and JP3 Epson SG8002DB, (U6) 50MHz Oscillator DIP14, 50MHz 50MHz, socketed Epson SG8002DB, (U5) 6.5MHz Oscillator DIP14, 6.5MHz 6.5MHz, socketed Seiko Epson Corporation S5U13706P00C100 Evaluation Board Rev. 1.2...
-
Page 21: Schematics
All manuals and user guides at all-guides.com Schematics 8 Schematics Figure 8-1: S5U13706P00C100 Schematics (1 of 5) Seiko Epson Corporation S5U13706P00C100 Evaluation Board Rev. 1.2... - Page 22 All manuals and user guides at all-guides.com Schematics Figure 8-2: S5U13706P00C100 Schematics (2 of 5) Seiko Epson Corporation S5U13706P00C100 Evaluation Board Rev. 1.2...
- Page 23 All manuals and user guides at all-guides.com Schematics Figure 8-3: S5U13706P00C100 Schematics (3 of 5) Seiko Epson Corporation S5U13706P00C100 Evaluation Board Rev. 1.2...
- Page 24 All manuals and user guides at all-guides.com Schematics Figure 8-4: S5U13706P00C100 Schematics (4 of 5) Seiko Epson Corporation S5U13706P00C100 Evaluation Board Rev. 1.2...
- Page 25 All manuals and user guides at all-guides.com Schematics Figure 8-5: S5U13706P00C100 Schematics (5 of 5) Seiko Epson Corporation S5U13706P00C100 Evaluation Board Rev. 1.2...
-
Page 26: Board Layout
All manuals and user guides at all-guides.com Board Layout 9 Board Layout Figure 9-1: S5U13706P00C100 Board Layout Seiko Epson Corporation S5U13706P00C100 Evaluation Board Rev. 1.2... -
Page 27: Change Record
• section 11 - update sales office addresses X31B-G-021-01 Revision 1.0 - Issued: March 19, 2007 • initial draft • minor edits • added parts list • added schematics • updated tech support contact information Seiko Epson Corporation S5U13706P00C100 Evaluation Board Rev. 1.2... -
Page 28: Sales And Technical Support
All manuals and user guides at all-guides.com Sales and Technical Support 11 Sales and Technical Support For more information on Epson Display Controllers, visit the Epson Global website. https://global.epson.com/products_and_drivers/semicon/products/display_controllers/ For Sales and Technical Support, contact the Epson representative for your region.